The current edition of the American National Standard "Installation of Gas Appliances and Gas Piping”, 221.30, takes precedence over all other reference publications pertinent to this installation instruction. Both models are shipped factory-assembled. Installation comprises the following: * L Inspection * II. Location and Suspension ♦III. Gras Piping IV. Wiring * V. Venting VI. Start-up and Adjustment VII. ,Service and Maintenance *To perform these sections (or installation steps), refe

Use adjusting screw under screw cap on pilot valve for this purpose. For D4 controls, flame should be long enough for good impingement on metal element of Bryant automatic pilot For D5 and D2 controls, flame should surround thermocouple element of pilot and extend downward to include 3/8 to 1/2 inch of thermocouple. Flame should never come in contact with any other part of thermocouple or its lead wire. To adjust pilot flame on units equipped with a Model A-643 valve, adjustment screw is locat

*Motor drive range: 830 to 1130 rpm. All other rpms require field-supplieddrive. 580F036- 151 71 580F036 151 580F036 151 PERFORMANCE DATA (cont) FAN PERFORMANCE — HORIZONTAL DISCHARGE UNITS (cont) 580F150,151 (121/2 TONS) — STANDARD MOTOR (BELT DRIVE)* Airflow (Cfm) External Static Pressure (in. wg) 0.2 0.4 0.6 0.8 1.0 Rpm Bhp Watts Rpm Bhp Watts Rpm Bhp Watts Rpm Bhp Watts Rpm Bhp Watts 3700 676 1.19 1106 747 1.42 1328 811 1.66 1552 871 1.91 1779 927 2.15 2008 3800 690 1.27 1185 760 1.52 1414 8

Copper Tubes, Aluminum Lanced, AluminumPre Coated, or Copper Plate Fins Rows...Fins/in. Total Face Area (sq ft) EVAPORATOR FAN Quantity...Size (in.) Type Drive Nominal Cfm Std Motor Hp Opt Motor Hp Motor Nominal Rpm Std Maximum Continuous Bhp Opt Maximum Continuous Bhp Motor Frame Size Fan Rpm Range Low-Medium Static High Static Motor Bearing Type Maximum Allowable Rpm Motor Pulley Pitch Dia. Low-Medium Static High Static Nominal Motor Shaft Diameter (in.) Fan Pulley Pitch Diameter (in.) Low-Med

The 585A/YACR is the natural or propane model supplied with the RELITE-type pilot that saves gas by operating only when the wall thermostat calls for heating. The 586A/YACX is the deluxe model with RELITE-type pilot and many value added features for reliability and performance. These units are designed for outdoor installation either on a rooftop or at ground level on a slab. The cooling section is factory-charged and sealed, minimizing installation time. Installation is easy—connect gas supply

Ib mount the disconnect on this panel, align one of the disconnect box knockouts with the unit high-voltage inlet hole and secure the box to the panel. Route the wiring from the disconnect through the aligned knockout and unit inlet. WARNING: Ensure that the drill does not damage any components when drilling through ihe panel. 2. Run high-voltage leads to unit control box and connect leads to contactor. See unit wiring label and Figure 11. NOTE: On 3-phase units, the third power lead is conne

The pilot flame then ignites the burners. The 821 heating blower relay (2G) was energized when the circuit through the thermostat was completed. After a short delay, the blower relay (2G) contacts close and the circuit to the blower motor (3D) is completed. This circuit energizes the motor to start the blower. When the thermostat is satisfied, the circuit between R and W within the thermostat will break. On units equipped with the glow-coil pilot, the circuit to gas valve (5A) is deenergized a

7267627267627275TC183.66166.86151.43194.90177.83162.05201.97SHC79.39100.52121.9191.70119.42147.05102.94kW9.829.639.469.589.769.9610.0485TC172.71156.78142.09183.32167.13152.17189.98SHC69.0390.92112.9580.69109.17137.5191.49kW10.8210.6310.4510.5710.7610.9611.0495TC161.37146.24132.38171.36156.04141.86177.62SHC58.4481.04103.7769.4298.67127.7179.83kW11.9211.7311.5611.6811.8612.0512.14 105TC149.57135.32122.21158.89144.45131.10164.74SHC47.5770.9294.3257.8587.91117.6167.79kW13.1212.9412.7712.8913.0613.24

Bhp — Brake Horsepower NOTE: Maximum continuous bhp for the standard motor is 6.13. The Watts — Input Watts to Motor maximum continuous watts is 5180. Do not adjust motor rpm such that motor maximum bhp and/or watts is exceeded at the maximum operat *Standard low-medium static drive range is 873 to 1021 rpm. Alternate ing cfm. See Table 24 for more information. high-static drive range is 1025 to 1200. Other rpms require a field- supplied drive. —27— Table 14 — Fan Performance — 580F180360 (High

For propane operation, conversion kit P/N 301625-703 must be field-installed. Model 585B units have two A.G.A.-certified heating input ratings. See Table I. These units are designed for outdoor installation either on a rooftop or at ground level on a slab. The cooling section is factory-charged and sealed, minimizing installation time. Installation is easy—connect gas supply, air ducts, condensate drain, high- and low-voltage wiring, and install the air filter. NOTE: An optional condenser coi