Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or operation, contact your authorized Pride Provider. WARNING! Do not service the power chair when the seat is occupied. Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of any kind. WARNING! Direct or prolonged exposure to water or dampness could cause thepower chair to malfunction electronically and mechanically. Water can cause electrical components to corrode and the chair's frame to rust. Power chairs shouldbe examined periodically for signs of corrosion caused by water exposure, bodilyfluid exposure, or incontinence. Damaged components should be replaced or treatedimmediately. Should your power chair come in contact with water: 1. Dry your power chair as thoroughly as possible with a towel. 2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate. 3. Check the joystick operation and the brakes before using your power chair again. 4. If any inconsistencies are found, take your power chair to an authorized Pride Provider. Power chairs that arefrequently exposed to sources of water, such as incontinence, should be inspected often for corrosion andelectronic components may need to be replaced frequently. Temperature • Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your power chair between the temperatures of 18°F (-8°C) and 122°F (50°C). • In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell). • Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reduced speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical components. General Guidelines • Avoid knocking or bumping the controller, especially the joystick. • Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture. • Keep the controller clean. • Check all connectors to ensure that they are all tight and secured properly. .. Make sure pneumatic tires are inflated to the psi/bar/kPa air pressure rating indicated on the tire. WARNING! Make sure your tires are inflated to the psi/bar/kPa air pressure raiting indicated on thetire for pneumatic tires. Do not underinflate or overinflate your tires. Low pressure may result inloss of control, and overinflated tires may burst. Overinflating tires can cause them to explode. WARNING! Do not use a high pressure hose to inflate your tires. • Use a rubber conditioner on the tire sidewalls to help preserve them. WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make thetires slippery and cause your power chair to skid. Jazzy 600 Series VII. CARE AND MAINTENANCE VII. CARE AND MAINTENANCE • All wheel bearings are prelubricated and sealed. They require no subsequent lubrication. • The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain its high-gloss appearance. • Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery tray, with the battery terminals facing inward, toward each other. Refer to the battery wiring label for the correct wiring layout. WARNING! Even though the power chair has passed the necessary testingrequirements for ingress of liquids, you should keep electrical connections awayfrom sources of dampness, including direct exposure to water or bodily fluids andincontinence. Check electrical components frequently for signs of corrosion andreplace as necessary. Daily Checks • With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot. Do not handle or try to repair it. See your authorized Pride Provider if there is a problem. • Visually inspect the controller harness. Make sure that it is not frayed, cut, or has any wires exposed. See your authorized Pride Provider if there is a problem. • Check for flat spots on solid tires. Flat spots could adversely affect stability. • Inspect the seating system, armrests, and front riggings for loose hardware, stress points, or damage. See your authorized Pride Provider if there is a problem. Weekly Checks • Disconnect and inspect the controller from the power base. Look for corrosion. Contact your authorized Pride Provider if necessary. • Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtight...
Otros modelos de este manual:Sillas de ruedas - Jazzy 600 2S (4.07 mb)
Sillas de ruedas - Jazzy 600 2SP (4.07 mb)
Sillas de ruedas - Jazzy 600 3S (4.07 mb)
Sillas de ruedas - Jazzy 600 3SP (4.07 mb)