(Right and left hand is determined by the location of the adjustment arm (3) in relation to the curve of the discs.) Insert bolt through discs and wood bearings (4) and fasten with washer and nut. Then clamp disc gangs to the tool bar (5) with clamps (6) to the rear as shown. ADJUSTMENTS Disc gangs are reversible and can be set to throw-in or throw-out. To reverse discs remove cotter pin from adjustment link (7), swing disc gang half way around and replace cotter pin. To angle discs for great

All rights reserved Housing & Rotor Group - Models 5/14 & 8/14 REF NO PART NO. QTY. DESCRIPTION 1 1729176SM 1 HOPPER LINER 2 1924874SM 4 WASHER, Flat, 5/16 3 1917356SM 12 * LOCKWASHER, Split, 5/16 4 1921332SM 2 CAPSCREW, Hex Head, 5/16-18 x 3/4 5 1960507SM 2 CAPSCREW, Phillips Head, 1/4-20 x 5/8 6 1931277SM 12 NUT, Hex Flange, 5/16-18 7 1920787SM 8 CAPSCREW, Hex Head, 5/16-18 x 1/2 8 1729174SM 1 COVER, Rotor Housing 9 2805100SM 1 KEY, 1/4 Sq. x 2-1/4 10 1729132SM 1 SPACER, Rotor (5/14 Only) (5/1

No. 1692902 500 N. Spring Street, P.O. Box 997 Port Washington, WI 53074-0997 USA Form Nos. 1717126 Rev. 4/97 © Copyright 1996 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA. TP 100-2056-00-CS-S Form Nos. 1717126 Rev. 4/97 © Copyright 1996 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA. TP 100-2056-00-CS-S OPERATOR’S MANUAL CHIPPER/SHREDDER WITH ELECTRIC START MODEL 6/14E Mfg. No. 1692904 Form Nos. 1717127 Rev. 4/97 © Copyright 1996 Simplicity Manufacturin

Push fully in and turn until it snaps into place. NOTE: Insert plug (3) into adapter when vacuum attachment is not in use. See Removing the Vacuum Kit on the next page. 4. Slip the grip (12) onto the handle (11). Putting some soap on the handle will make the grip slide on easier. 5. Connect the handle to the nozzle (6) using the screw (10), washers (9) and nut (8). 6. Connect nozzle (6) or leaf tray (5) to the hose,. 7. Securely place hopper lid (14) on hopper. Ref. Qty. Part No. 1A 1 10

The strength of the vacuum can be adjusted by turning the sleeve on the nozzle end. Open the sleeve fully for minimum suction power to vacuum leaves over a garden area. VACUUMING TIPS • Keep the hose straight for best performance. • Rake leaves into the tray at a steady rate so that the engine or motor runs at an even level. For best results, do not cram the tray full of leaves. • Avoid items, such as twigs, that can get caught in the hose. • If material is wet, allow to dry before vacuumin

No. Description Attachment 1694678 8/14 Chipper/Shredder 1694896 814 Chipper/Shredder 1694897 5515 Chipper/Shredder 1694898 5/14 Chipper/Shredder (CE/Export) 1694910 5514 Chipper/Shredder 1731143Part No.: Parts Manual Rev. 09/2007 5/14 & 8/14 Series Chipper/Shredders TP 400-4096-01-CS-S Mfg. No. Description Attachment 1694678 8/14 Chipper/Shredder 1694896 814 Chipper/Shredder 1694897 5515 Chipper/Shredder 1694898 5/14 Chipper/Shredder (CE/Export) 1694910 5514 Chipper/Shredder 1731143Part No.: Ta

Nos. 1692210, 1692231, 1692353, 9000100 A WARNING Turn off the engine, let the rotor come to a complete stop and disconnect the spark plug wire before assembling the vacuum kit or changing attachments. A WARNING Never remove% adapter from the back of the machine while the machine is running or the rotor is turning. The rotor is pinning just inches away from the adapter iniet. Serious injury will result if you put your fingers or foot in the adapter inlet while the rotor is turning! INSTALL

Only kit. *2480 Adjust vacuum strength by turning ring and adjusting opening size. Figure 1. Kit Parts FORM - 1709566 PRINTED IN U.S.A. 12/93-SMI USING THE VACUUM The vacuum kit lets you take full advantage of the vacuum created by the four fan blades on the rotor flywheel. Placing the lid on the hopper directs the suction power to the hose inlet at the bottom of the housing. Use the vacuum kit to conveniently rake dry leaves and grass clippings into the leaf tray, where the material is s