Votos - 1, Puntuación media: 4 ( )

Fabricar: Enerco Tamaño del archivo: 998.73 kb Nombre del archivo: Idioma del manual:

This will allow air to bleed from the gas system. 6. Push in control knob and rotate control knob back to OFF position then rotate counterclockwise to PILOT/IGN position. This will light pilot. If needed gently keep rotating control knob back and forth while depressed until pilot lights. WARNING: When running heater, set control knob at “LO” or “HI” locked positions. Poor combustion and higher levels of carbon monoxide may result if heater is operated with control knob positioned between locked positions. LOW Control Knob 7. Keep control knob depressed in for ten (10) seconds after lighting pilot. If pilot goes out, HIGH repeat steps 4, 5, 6 and 7. • If pilot does not stay lit, refer to Troubleshooting, pages 14 & 15. Also, contact a qualified service OFF person or gas supplier for repairs. • If control knob does not pop up when released, contact a qualified service person or gas Figure 18. supplier for repairs. IMPORTANT: Release downward pressure while 8. FOR IR10LP: When the pilot is lit, turn the turning control knob. Control knob must be locked at control knob to “LO” position to light heater. the desired position. Leave on “LO” position until first burner tile has turned bright red. FOR BF10LP: When the pilot is lit, turn the control knob to “HI” position to light heater. 9. FOR IR10LP: After first burner tile has turned bright red, adjust heat output by turning control knob to desired position (“LO” or “HI”). Do not operate heater between locked positions. 10 Installation instructions and Owner’s Manual 70575 Rev. C 8/05 TO TURN OFF GAS TO APPLIANCE TO TURN OFF GAS TO APPLIANCE 1. Turn control knob clockwise to the OFF position. 2. Turn off all electrical power to the appliance if servicing is to be preformed. 3. Turn off equipment shutoff valve. SHUTTING OFF BURNER ONLY (PILOT STAYS LIT) 1. Turn control knob clockwise to the PILOT/IGN position. OPERATING YOUR HEATER THERMOSTAT MODELS TSIR20LPT, TSIR30LPT, TSBF20LPT, TSBF30LPT, MHIR20LPT, MHIR30LPT, MHBF20LPT, MHBF30LPT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call you gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you can not reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If knob will not push in or turn by hand, don’t try to repair it call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system which has been underwater. LIGHTING INSTRUCTIONS 1. STOP! Read the all safety information included with and on the side of heater. 2. Make sure the equipment shutoff valve is fully open. 3. Push in gas control knob and slightly turn clockwise to the OFF position (see figure 19). 4. Wait five (5) minutes. Then smell for gas including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you do not smell gas, go to the next step. 5. Push in and turn control knob counterclockwise to PILOT/IGN. Press in control knob for five (5) seconds. Note: The first time that the heater is operated after connecting the gas supply, the control knob should be depressed for about 30 seconds. This will allow air to bleed from the gas system. Control Knob Ignitor Button Figure 19. 6. With control knob pressed in, push down and release the ignition button. This will light pilot. If needed keep pressing igniter button until pilot lights. 7. Keep control knob pressed in for (30) seconds after lighting pilot. After 30 seconds, release control knob. Figure 20 • If pilot does not stay lit, refer to Troubleshooting, pages 14 & 15. Also, contact a qualified service person of gas supplier for repairs. • If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs. 11 Installation instructions and Owner’s Manual 8. When the pilot is lit, turn control know counterclockwise to heating level. The main burner should light. 9. To select the desired heat level, turn the temperature setting knob counterclockwise to between 1 & 7. THERMOSTAT CONTROL OPERATION FOR IR20LPT / IR30LPT: The thermostatic control used simply turns on and off the burner. FOR BF20LPT / BF30LPT: The thermostatic control u...

Descargar ahora

Introduzca dos números de la imagen: