Iniciar sesión:
Votos - 5, Puntuación media: 3.8 ( )

Manual de usuario Chromalox, modelo ELECTRIC SAUNA HEATER JM-30

Fabricar: Chromalox
Tamaño del archivo: 841.43 kb
Nombre del archivo:
Idioma del manual:
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Heating of the Sauna When the heater is switched on for the first time, both theheaterandtherocksemitsmell.Toremovethesmell, the sauna room needs to be efficiently ventilated. The purpose of the heater is to raise the temperature of the sauna room and the sauna rocks to the required bathing temperature. If the heater output is suitable for the sauna room, it will take about an hour for a properly insulated sauna to reach that temperature. See item 2.1., .Insulation and wall materials of the Sauna Room.. A suitable temperature for the sauna room is about+150°F.+175°F(+65°C.+80°C). The sauna rocks normally reach the required bathing temperature at the same time as the sauna room. If the heatercapacityistoobig,theairinthesaunawillheatvery quickly, whereas the temperature of the rocks may remain insufficient; consequently, the water thrown on the rocks will run through.Onthe other hand, if the heater capacity is too low for the sauna room, the room will heat slowly and, by throwing water on the rocks, the bather may try to raise the temperature of the sauna. However, the water will only cool down the rocks quickly, and after a while the sauna will not bewarmenough and the heater will not be able to provide enough heat. In order to make bathing enjoyable, the heater capacity should be carefully chosen to suit the size of the sauna room. See item 2.3. .Heater Output.. 1.3. Control Unit 1.3.1. Timer The heaters JM-17 and JM-20 are switched on by using the timer switch. The indicator lights will come on. The timer has two scales: the first one (with larger figures) is the .instantly on. section; that is, the heater is on for a selected period of time (0.1 hours). The other section is the so called .pre-set section. (1. 8 hours), which is used to start the heater after a certain time. The heater starts when the timer has turned the switch back to the .instantly on. section, that is, at number one(1). After this, the heater will be on for about 1 hour, unless the switch is turned to zero before that. At zero (0), the supply to the elements is cut off and the heater is switched off. See fig 2. The JM-30 heater is equipped with 1 hour timer without pre-set time function. See fig. 2. If you wish to use the full 60 min. cycle, turn the timer knob past the first 1 to number 2 or 3 on the dial. Then turn backward to the large 1 until a click is heard. Leave knob at that setting, and Sauna will operate for 1 hour before shutting off automatically. Figure 2. Control panel Figure 1. Piling of the sauna rocks Example 1. You want to go jogging and have a sauna bath after that. The estimated duration of your run is 5 hours. Turn the timer clockwise over the scale 0.1 to the preset section (scale 1.8) at number 4. The timer will start, and after four hours, the heater will come on. Because i...

Otros modelos de este manual:
Eléctrico - ELECTRIC SAUNA HEATER JM-20 (841.43 kb)
Eléctrico - ELECTRIC SAUNA HEATER JM-17 (841.43 kb)
Eléctrico - ELECTRIC SAUNA HEATER JM-17 (841.43 kb)
Eléctrico - ELECTRIC SAUNA HEATER JM-17 (841.43 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría