Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
K • 11/06 10 Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 Part number list on following page. 7 Log Assembly (NG, LP) Exploded Parts Diagram Service Parts RCOR-HV-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ 1 2 4 3 15 5 6 Grate Bar Service Parts List (NG, LP) RCOR-HV-IPI IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts. AVAILABLE TO SHIP IN 24 HOURS ITEM COMMON PARTS SERIAL # PART NUMBER • Burner Orifice NG (#32DMS) 582-832 Y Burner Orifice LP (#50DMS) 582-850 Y 1 End Glass Assembly GLA-MS Y 2 Glass Door Assembly GLA-6TROC Y 3 Burner Assembly 2005-006 Y 4 Log Grate 2005-012 5 Side Refractory SRV2005-730 6 Refractory, Back SRV2005-731 7 Log Set Assembly LOGS-MSR Y 8 Log 1 SRV2005-701 9 Log 2 SRV2005-700 10 Log 3 SRV2005-702 11 Log 4 SRV2005-703 12 Log 5 SRV2005-704 13 Log 6 SRV2005-705 14 Log 7 SRV703-703 Lava Rock Bag 2005-790 Flue Restrictor 385-128 Teco-Sil, 5 lb. bag 700-790 Ember Mesh Assembly 2006-008 Y Non-Combustible Board (side) 2006-136 Non-Combustible Board (end) 2008-114 Junction Box 4021-013 Y 3V Adaptor Plug 593-593A Y Battery Pack 593-594A Y Fiberglass Rope 060-455 Glass Latch Support Assembly 386-122A Y Mineral Wool 050-721 Conversion Kit NG NGK-MS Y Conversion Kit LP LPK-MS Y ACCESSORIES Fan Kit GFK-160A Remote Control Kit RC-SMART-HNG Remote Control Kit SMART-STAT-HNG Remote Control - Multi-functional RCT-MLT-HNG Wall Switch, Multi-functional WSK-MLT Plug Adapator Kit (for WSK-MLT) PLUG-ADP Louvers with Mesh MS-LOUVERS Louvers with Mesh - End Panel MS-LOUVERS-EP Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 12 Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 (NG, LP) Exploded Parts Diagram Service Parts L&RCOR-HV-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ PIER-HV-IPI, ST-HV-IPI NOTE: Replacement bulbs to be supplied by homeowner. Recommended replacements: Sylvania Mini Candelabra 75 watts. 1 2 4 5 6 7 9 8 10 3 11 12 13 14 AVAILABLE TO SHIP IN 24 HOURS ITEM DESCRIPTION SERIAL # PART NUMBER 1 ON/OFF Rocker Switch 060-511 Y 2 ON/OFF Wire Assembly 060-521A Y 3 Valve NG 750-500 Y 3 Valve LP 750-501 Y 4 Flexible Gas Connector 2005-009 Y 5 Module 593-592 Y 6 Wire Assembly 593-590A Y 7 Ember Box Assembly 2005-114 Y 8 Pilot Assembly NG 385-510A Y 8 Pilot Assembly LP 385-511A Y 9 Pilot Bracket 2005-118 10 Gasket Orifice 2005-166 11 Valve Bracket 2005-120 12 Flex Ball Valve Assembly 302-320A Y 13 Pilot Assembly Support 385-120 14 Ground Strap 385-512 Regulator, NG NGK-DXV Y Regulator, LP LPK-DXV Y Pilot Tube 446-301 Y Orifice Spud NG 446-505 Y Orifice Spud LP 446-517 Y 1Approvals and Codes Appliance Certification The Heat & Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certification MODELS: PIER-HV-IPI, ST-HV-IPI, LCOR-HV-IPI, RCOR-HV-IPI LABORATORY: Underwriters Laboratories TYPE: Direct Vent Gas Fireplace Heater STANDARD: ANSI Z21.88•CGA2.22•UL307B Installation Codes The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections. In the absence of local codes, the fireplace installation must conform to the National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-B149 Installation Codes (in Canada). The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the CSA C22.1 Canadian Electric Code (in Canada). These models may be installed in a bedroom or bed-sitting room in the U.S.A. and Canada. High Altitude Installations U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2,000 feet in the U. S. A. and in Canada. When installing this appliance at an elevation above 2,000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility. If installing this appliance at an elevation above 4,500 feet (in Canada), check with local authorities. Heat & Glo Quality Systems registered by SGS ICS Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 NOTE: The following requirements reference various Massachusetts and national codes not contained in this document. Inspection The state or local gas inspector of the s...
Otros modelos de este manual:chimeneas - PIER-HV-IPI (3.11 mb)
chimeneas - RCOR-HV-IPI (3.11 mb)
chimeneas - ST-HV-IPI (3.11 mb)