Si requiere retroceder un articulo despues de haberlo insertado en los rodillos oprima el boton de retroceso y el articulo saldra por la puerta frontal. NOTA: Es posible que los elementos laminados que salen de la maquina esten demasiado calientes al contacto. NOTA: Los elementos laminados estaran calientes y se doblaran facilmente. Para mantenerlo firme, coloquelo sobre una superficie plana y dejelo enfriar. Laminacion en frio 1. Coloque la maquina en un piso, superficie resistente y pulse el b

Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left si

Laminacion en Calienta y en Frio La maquina puede ajustarse para manejar bolsas de pelicula de laminacion fria y caliente. Control de la Temperatura Configuraciones individuales para diferentes espesores de pelicula 3-10 mil. Luz de Preparcion Una luz de preparcion indica cuando la maquina ha alcanzado la tempertura optim y esta lista para la laminacion. Velocidad Rapida Laminados de hasta 20” por minuto. Automatico de Cierre de Funcion La maquina se apagara automaticamente despues de una hora d

LIMITED WARRANTY This warranty specifically does not cover damage to laminating rollers caused razor blades, or any sharp objects or abrasives, or failure caused by adhesives, damage caused by lifting, tilting and/or any attempt to position the machine rolling on the installed castors or feet on even surfaces, or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its Reseller(s) does not extend the warranty beyond the initial one year date of installation. Unauthor

2. FUNCTIONS OF BUTTONS : Upper roller temperature controller : Lower roller temperature controller UPPER SPEED LOWER UPPER SPEED- 14 - : Speed controller : Choose memorized working condition : . Increase temperature . Increase speed . Restore the memorized working setting : . Decrease temperature . Decrease speed . Restore the memorized working setting : Cold and Hot mode change : Check current temperature : Saving electricity while the machine is not being operated. : Reverse function Stay pre

There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension. 2. COLD LAMINATING 1. Put cold roll film on upper bar.(Set the same as methord of HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. - 2

Set material on Mount board then slide them into the opening slot 5. Finished board will exit through the rear slot of machine. 6. When finish, press the power button and turn off. * The document, which has been mounting board laminated, is pretty hot and easily bent. Try not to touch the document until it has cooled down. * When laminating to mounting board 2mm, pressure adjustment is needed for good quality lamination. 1. Unscrew 6 retaining screws of bottom and lift off top cover. 2. Locate e

7. Turn off the power when unattended or not in use. Unplug machine before movig it or when it is not in use for an extended period of time. 8. This machine is intended for indoor use only. 9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply. 10. The socket-outlet shall be installed mear the equipment and shall be easily accessible. - 3 CHARACTERISTICS RS Roll Laminator Line are advanced laminators with time transcendental design, utilizing the latest in