Always stop tool operation and charge the battery cartridge when you notice less tool power 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C -40°C (50°F -104°F). Let a hot battery cartridge cool down before charging it. Hex wrench storage When not in use, the hex wrench can be Hex wrench conveniently stored. CAUTION: Always be sure that the tool is switched off and the battery cartri

5046DB 160 mm (6-1/4") MODEL 5046DWA, S046DWB With High Capacity Battery Charger INSTRUCTION MANUAL SPECIF1CAWONS 1 1 I I MODE7 Blade diameter Cutting depth No I ~ ~ ~ Overall length ~ ~ e d Net weight 5026D I 165 mm 16.112") I 55 mm 12-3/16")I 2,400 I 338 mm 113-5116',)I 3.8kg (8.4Ibs) 5036D I 160mm 16-114")1 53 mm (2-1/16"]I 2,400 I 338mm (13-5116")I 3.8kg 18.4Ibs) Battery Cartridge 1822 Model DC1801 High Capacity Battery Charger Voltage Input output Charging time 18 V A.C. only 50 -60 Hr O.C.

When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off. I To avoid kickback do support board Don't support board or panel away or panel near the cut. from the cut. I Fig. Fig. 2 5 Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before

To remove the blade, first remove the hex socket head bolt which secures the dust box, then remove the dust box. Thumb screw - After installing the blade, install the dust box and tighten the hex socket head bolt to secure the dust box. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the bolt clock- wise. Then remove the bolt, outer flange and blade. Hex wrench (Counterclockwise) Then remove the hex socket head bolt. outer flange and bl

Turning off controls will not reduce this risk. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3.Do not allow anything to cover or clog the charger vents. 4.Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flo

Tools are dangerous in the hands of untrained users. When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. Chec

Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools-Electric': ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Hex wrench *Rip fence (g

If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the high capacity battery charger. If the charging light flashes alternately in green and red color, a problem exists and charg ing is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. Trickle charge (Maintenance charge) If you leave the battery

This tool is equipped with the dust box to Dust cap collect dust and cut chips. For the best cut- ting performance, empty the dust box each time the battery cartridge is completely dis- charged. Press the lever and open the dust cap. Tip the rear of the tool down to empty the dust box. Cleaner cutting operations can be per- formed by connecting this tool to Makita vacuum cleaner. Remove the rubber cap from the dust cap and connect the hose of vacuum cleaner to the dust cap. Switch action CAUTION

After adjusting the depth of cut, always tighten the lever securely. Sighting When cutting, align the left side of notch in the front of the base with your cutting line on the workpiece. Dust collection CAUTION: Never cut workpieces covered/stained with thinner, gasoline, oil or the like. If the dust box is stained with them, it may crack, causing an injury to operator. This tool is equipped with the dust box to Dust cap collect dust and cut chips. For the best cut- ting performance, empty the d