Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
If any pieces are missing, contact your Garmin dealer immediately. Use the following instructions to install the AIS 300 device. Details for the following steps are included in this document: 1. SelectlocationsfortheAIScomponents. 2. MounttheAIS300receiverbox. 3. ConnecttheAIS300topower. 4. ConnecttheAIS300toaVHFantennaandtoanoptionalVHFradio(page4). 5. ConnecttheAIS300toaNMEA2000networkortoaNMEA0183-compatiblechartplotter(optional -page4). . WARNING When navigating, carefully compare information provided by the unit to all available navigation sources, including information from visual sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing navigation. Use this unit only as a navigational aid. Do not attempt to use the unit for any purpose requiring precise measurement of direction, distance, location, or topography. This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is provided in accordance with California’s Proposition 65. See for more information. . CAutIoN Wear safety goggles and a dust mask when drilling, cutting, or sanding. Safe Compass Distance Ensure that you install the AIS 300 receiver box at least 15 3/4 in. (40 cm) from any compass. Test your compass to verify that it operates correctly when the AIS 300 is operating. Selecting Locations for the AIS 300 Components Use the wiring layout diagrams starting on page 2 to determine how to best organize the AIS 300 components on your boat. Ensure that the cables reach all components before permanently mounting any component. Mounting the AIS 300 Receiver Box Install the AIS 300 receiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the location is well ventilated and away from objects that generate heat. Ensure that the receiver box is at least 15 3/4 in. (40 cm) from any compass to avoid interference. Needed tools • Drill and drill bits • Number 2 Phillips screwdriver to mount the receiver box: 1. Ensure that the chosen location is dry, protected from washdown, and well-ventilated. 2. Use the receiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the receiver box. 3. Drill four 1/8 in. (3 mm) pilot holes. 4. Mount the receiver box using the included 20 mm M 3.5 screws. You can also use bolts, washers, and nuts (not included) to mount the receiver box if the mounting surface is suitable. March 2010 190-01178-00 Rev. B Printed in China AIS 300 Installation Instructions * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. RF interconnect cable (included) Chartplotter (optional - not included) NMEA 2000 network—page 4 12 or 24 Vdc AIS 300 power/data cable NMEA 2000 drop cable (included) Chartplotter power VHF radio power NMEA 2000 network power (not included) AIS 300 receiver box RF cable to VHF antenna (not included) VHF radio* (optional - not included) AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter Through NMEA 2000 AIS 300 Installation Instructions AIS 300 power/data cable > > > > 12 or 24 Vdc Chartplotter power VHF radio power VHF radio* (optional - not included) Garmin NMEA 0183- compatible chartplotter (optional - not included) RF interconnect cable (included) AIS 300 receiver box RF cable to VHF antenna (not included) Gray [Tx A (+)] Pink [Tx B (-)] Yellow [power toggle] Wire color [function] White [Rx A (+)] Orange/White [Rx B (-)] Orange [Accessory On] Wire color [function]** AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter Through NMEA 0183 * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. ** The listed wire colors are for the NMEA 0183 Port 1 input on a Garmin GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter. Refer to the installation instructions provided with your Garmin chartplotter if you want to connect the AIS 300 to a different model of Garmin chartplotter or to a different NMEA 0183 port on a GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter. If you are connecting the AIS 300 to a non-garmin chartplotter, see page 5 for detailed wiring assignments. Connecting the Receiver Box to Power Use the AIS 300 power/data cable to connect the receiver box to a 12 or 24 Vdc battery. Notes: • Connect the red wire to the positive battery terminal, and connect the black wire to the negative battery terminal. • The replacement fuse on the power/data wiring harness is a 5 A, fast-acting fuse. • If it is necessary to extend the power wires, use 16 AWG or larger wire. • If your boat has an electrical system, you can possibly connect the AIS 300 directly to an unused holder on your fuse block. If you...
Otros modelos de este manual:equipamiento barco - NMEA 0183 (1.62 mb)
equipamiento barco - AIS 300 (1.62 mb)