Professional installation of the autopilot system is highly recommended. Specific training in hydraulic pipe-fitting and in marine electrical connections is required to properly install the autopilot system. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin Product Support. note: If your boat uses a Mercury® Verado® engine, you must also purchase a Mercury Verado Adapter Kit (Garmin part number 010-112

If the handheld compass does not point north when you hold it in the location you want to mount the CCU, then there is magnetic interference. Choose another location and test again. GHP 10 Marine Autopilot System Installation Instructions Opening for cablesMounting screws (. ) ThumbscrewOpening for cables Mounting screws (. ) Thumbscrew 26 GHP 10 Marine Autopilot System Installation Instructions If possible, mount the CCU within 16 ft. (5 m) of the ECU. If you cannot mount the CCU within 16 ft.

Para obtener mas informacion sobre NMEA 2000, visite ADVeRteNCIA: consulte la guia Informacion importante sobre el producto y su seguridad que se incluye en la caja del producto y en la que encontrara advertencias y otra informacion importante sobre el producto. Registro del producto Complete hoy mismo el registro en linea y ayudenos a ofrecerle un mejor servicio. Conectese a nuestro sitio Web en Guarde el recibo de compra original o una fotocopia en un lugar seguro. Para futuras consultas, anot

Visit the Garmin Web site (for current updates and supplemental information concerning the use and operation of this and other Garmin products. Garmin®, GPSMAP®, AutoLocate®, TracBack®, BlueChart®, and MapSource® are registered trademarks of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin. December 2006 Part Number 190-00665-00 Rev. B Printed in Taiwan IntroductIon > InstallIng Your gMr 21/41 and about thIs Manual IntroductIon This manual covers the f

To connect the VHF 300 series radio to your existing NMEA 2000 network: 1. Determine where you would like to connect the radio to your existing NMEA 2000 backbone. 2. Disconnect one side of a NMEA 2000 T-connector from the backbone at an appropriate location. If you need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable to the side of the T.connector you disconnected. 3. Add a T.connector (not included) for the radio to the NMEA 2000 backbone by connecti

3. Drill four 1/8 in. (3 mm) pilot holes.* 4. Mount the transceiver box using the included M4.2.25 screws. You can also use bolts, washers, and nuts (not included) to mount the transceiver box if the mounting surface allows. Connecting the Transceiver Box to Power Use the VHF 300 power/data cable to connect the transceiver box to a 12 Vdc battery through an external switch. Notes: • Use the VHF 300 Power Wiring-Assignment Table to identify the positive and negative wires. • The replacement fuse

Use at least 22 AWG wire for extended runs of wire, if needed. GHS 10 Cable W GHS 10 Cable WGHS 10 Cable Wiring-Assignment T iring-Assignment Tiring-Assignment Table ableable NotICe: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from seeping into the radio. Installing the Bulkhead Pass-Through Plate 1. Route the GHS 10 active speaker cable (or the GHS 10 cable) to the location you want to install the bulkhead pass-through plate. 2. Dril

Before you begin the installation: • Read these instructions thoroughly. • Gather the appropriate fasteners and tools. • Verify that all cables can reach the radio mounting location. • Wear safety goggles and a dust mask when drilling, cutting, or sanding. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. Contact Garmin Contact Garmin Product Support if you have any questions while

NOte: on a 4000 or 5000 series chartplotter, your service package appears on the system information screen (Configure > System > System Information > Weather Subscription) XM Radio: Highlight the Audio sub tab and verify that channels 7, 9, 47, and 122 are being received (see page 22). This indicates that all channels on XM’s basic radio service are being received. If within an hour the XM WX Weather and/or the XM Radio service has not activated, call XM customer care at 800-985-9200 to refresh

Moving away from a Low Pressure Center in any horizontal direction results in increased pressure. Winds flow counterclockwise around Low Pressure Centers in North America. Indicates a High Pressure Center. Similar to a Low Pressure Center, a High Pressure Center is an area where the measured pressure is highest relative to the surrounding area. Moving away from a High Pressure Center in any horizontal direction results in decreased pressure. Winds flow clockwise around High Pressure Centers in N