(Messages printed out automatically.) Manual Printing (MANU) Setting Press [[ o 1 key. No. Printing Timing of I o j key pressing Example Printout 1 Contents of {MF/HF call message} (VHF) (Select on “CALL” menu.) During “MF/HF call message” diplay to (VHF) “Ready for calling” display. © 2 Contents of all transmitted logs {Xmitted log No. < >} (Select on “XMT” menu.) Displayed TXmitted log No. < >J (To stop printing, press ( cancel j ■) 1 - 34 j /■ No. Printing Timing of [j o jkey pres

Installation Instructions) [ROM Version No.: 40] For the sake of brevity, we use the term "DSC-5 (R)“ to refer to both the DSC-5 (hanger type) and DSC-5R (rack mount type). f FURUNO ELECTRIC CO., LTD. I NISHINOMIYA, JAPAN ©FURUNO ELECTRIC CO., LTD. 9-52, Ash i hara-cho, N i sh i nom i ya, Japan 662 Telephone: 0798-65-2111 Telefax: 0798-65-4200 All rights reserved. ; Printed in Japan FIRST EDITION T APR 1991 OCT. 29, 1 997 (TATA) PUB. No. OME—55220 DSC—5/5R *00080215800* 00080215800

Qty Remarks Conversion Cable 02S4147 000-141-082 1 For water temperature and spd/temp sensors Water Temperature & Speed Sensor ST-02MSB 000-137-986 1 Thru-hull type ST-02PSB 000-137-987 Water Temperature T-02MTB 000-040-026 1 Transom mount, w/8 m cable T-02MSB 000-040-040 Thru-hull mount T-03MSB 000-040-027 Thru-hull mount, w/8 m cable Inner Hull Kit S 22S0191 000-802-598 1 Matching Box MB-1100 000-041-353 1 For connection to 1 kW transducer For FCV585 Transducer 50B-6 000-015-042 1 10 m, 1 kW 5

Flat washer Cable gland Vinyl sheath Clamping gland Gasket Cut and trim armor. Connect each cable cores to the terminal board, referring to the interconnection diagram on next page. 15 14 13 12 11 10 98 76 5 4 3 21 RG12/UY RG-12/UY TTYCY-4 DPYCY-6 RW-9600 Connect inner conductors. M8 screw for grounding Clamp outer conductor of coaxial cables. Fix wires with cable-tie. 4. INSTALLING OPTIONAL EQUIPMENT Processor unit Junction box Antenna unit Junction box RED[B] GRN[B] WHT BRK GRN RED WHT[B] PPL[

MOUNTING..................................... 1-1 1.1 Antenna Unit.................................1-1 1.2 Monitor Unit..................................1-6 1.3 Control Unit................................1-10 1.4 Processor Unit............................1-15 2. WIRING........................................2-1 2.1 Interconnection.............................2-1 2.2 Antenna Unit.................................2-2 2.3 Monitor Unit..................................2-6 2.4 Processor Unit.........

WIRING...............................................................................................2-1 2.1 Distributor Unit DS-610..............................................................................................2-2 2.2 Transceiver Unit DS-620 ...........................................................................................2-5 2.3 Display Unit DS-600, Remote Controller RD-501/Dimmer Controller RD-502 (option) ...............................................................

These units can be installed on a tabletop or flush mounted in a console or panel. 1.1.1 General mounting considerations • Keep the monitor unit out of direct sunlight. • Select a location where the unit(s) can easily be operated while observing the fishing ground or area surrounding the vessel. • For maintenance and checking purposes, leave sufficient space at the sides and rear of the unit and leave slack in cable. (Refer to the outline drawing at the back of this manual.) 1.1.2 Mounting Unibo

• If the D-sub connector is too large to pass through the hole in a bulkhead, etc. remove it, pass the cable through the hole and then reattach the connector. 2. WIRING Note 1 Hull unit 12/24 VDC 12-24 VDCLoudspeaker (w/cable) Motion sensor Clinometer Remote controller Navigation equipment 06S4078 (5/10m) 250V-DPYCYS-2.5 06S4080 (15/30/50m) 06S4081 (3.5/5.2m) DPYCYS-2.5 06S4037 (10m) Note 1: Optional cable between the monitor unit and control unit for separate installation -MJ-A10SPF0002-015 (1.

30 m. • The output from a funnel or exhaust vent decreases aerial performance and hot gases can damage the radiator. The antenna unit must not be installed where the temperature is more than 55° C. • The antenna unit can be installed on the bridge, a common mast, or the radar mast. (c) Radar mast(b) Common mast (a) On bridge Installation procedure Refer to the outline drawing at the back of this manual for the dimensions. Make five holes in the platform. Four holes to fasten the antenna unit and

HOW TO INSTALL THE SYSTEM.....................................................................................1-1 1.1 Display Unit ............................................................................................................... 1-1 1.2 Antenna Unit for MODEL1835 .................................................................................. 1-3 1.3 Antenna Unit for MODEL1935/1945 ......................................................................... 1-9 2. CABLE CONNECTION .