Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
• Turn shredding attachment upwards until it engages. • Attach filling tray. • Place a bowl or plate under the outlet opening. • Insert the mains plug. • Place the food to be processedin the feed tube. • Insert pusher and hold in place. Note: Pusher can be inserted in one direction only. Note position of the curve! • Switch on the appliance (I). • Press food down using the pusher. Do not exert too much pressure! After using the appliance: • Switch off the appliance (0). • Remove mains plug. • Pull out the pusher. • Remove the shredding attachmentHolding down the release button, turn the attachment to the right and remove. • Disassemble shredding attachment. Disassembly is in reverse order. • Clean all parts, see “Cleaning andservicing”. Grain mill attachment For grinding products such as wheat, oats, rice, ground coffee, pepper corns, wildmustard, walnuts, hazel nuts, dried mush rooms, almonds, soya, linseeds, buckwheat groats, shelled sunflower seeds, etc. The appliance is not intended to be used for grinding very hard products such as dried peas, maize or popcorn. Important information When the mill is attached, never use reverse. Attachment may be damaged! Fig. . Assembling grain mill attachment • Insert worm gear into the housing. • Insert grinding ring into the housing. Note shape of the parts! • Insert grinding cone. In doing so, the square head must be inserted into the opening of the worm gear. • Place grinding chamber on the housing. Lug on the grinding chamber must be in the recess on the housing. • Screw on threaded ring clockwise. Do not tighten the threaded ring too tight. • Screw on adjusting ring. • Put the grain mill attachment, inclinedslightly to the right, on the drive. • Turn grain mill attachment upwardsuntil it engages. • Tighten threaded ring. • Attach filling container. Working with the grain mill attachment Riskof injury! – – KeeDonocontpfingers out of the filling container. tinsertanyobjectsintothefil llingainer. • Place a bowl or plate under the outlet opening. • Insert the mains plug. • Put material to be ground into the fillingcontainer. • Set required degree of grinding on the adjusting ring: 1 = finest degree of grindingSTOP = coarsest degree of grinding Important information Degree of grinding can be re-adjusted in small steps during operation. Never unscrew adjusting ring over STOP, grinder may be damaged. • Switch on the appliance (I). The appliance may be operated continuously for a maximum of 15 minutes. Then leave the appliance to cool down for 45 minutes! Robert Bosch Hausgerate GmbH en Information on grinding – Do not grind oleaginous products at the smallest degree of grinding. The grinder may jam or become blocked. – In the case of softer grain, such as oats or linseeds, the coarse setting must be selected for grinding. – Do not grind dry poppy seeds. Poppy seeds must be boiled andsoaked for several hours before they can be ground. – Wash the grinder thoroughly whenchanging from one product to another. This will prevent odours from impairingeach other. – Caution during the grinding process, as particles may sometimes jump up and hit you in the eye. After using the appliance: • Switch off the appliance (0). • Remove mains plug. • Remove the grain mill attachment. Holding down the release button, turn the attachment to the right and remove. • Disassemble grain mill attachment. • Clean all parts, see “Cleaning andservicing”. Citrus press attachment For pressing the juice out of citrus fruits, e.g. lemons, oranges, grapefruits. Fig. . • Open the cover on the storagecompartment all the way. • Tilt the mincer so that the drive faces upwards. Cover on the storage compartment is used as a base. • Insert driver into the drive. • Place housing on the drive and turnit until it locks into position. Outlet faces forwards (Fig. .–6). • Insert filter tray and pressing cone. • Place a suitable receptacle under the outlet. • Insert the mains plug. • Switch on the appliance (I). • Press fruit onto the pressing cone. After using the appliance: .Switch off the appliance (0). .Remove mains plug. .Remove pressing cone and filter tray. .Remove housing. Holding down the release button, turnthe attachment to the left and remove. .Remove driver. .Clean all parts, see “Cleaning and servicing”. Cleaning and servicing Important informationIf there is too much fruit pulp in the filter, liquid may run into the appliance motor. If the filter is blocked with fruit pulp: – Switch off the appliance, – Remove and empty filter. Important informationThe appliance requires no maintenance. Thorough cleaning protects the appliance from damage and keeps it functional. Warning! Do not use abrasive cleaning agents. Surfacesmay be damaged. Do not clean the aluminium parts (housing, worm gear and threaded ring of the mincer attachment) in the dishwasher. Harmlessdiscolouration may occur overtime. Cleaning the appliance .Pull out the mains plug. .Wipe the mincer clean with a damp cloth. If required, use a little ...