Votos - 3, Puntuación media: 4 ( )

Fabricar: Craftsman Tamaño del archivo: 1.55 mb Nombre del archivo: bb107a2d-f2a6-4855-af06-553be42faa13.pdf Idioma del manual:

Remove any obstructions with the nozzle cleaning tool provided and backflush with clean water. 5. Direct water supply into spray wand to backflush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun and turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high- temperatures or dusty conditions, more frequent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. NOTE: The frame is equipped with an oil drain hole to help make changing the engine oil easier. PUMP The oil in the high pressure pump was designed to last the life of the pump. If there is a problem with the pump contact an Authorized Service Center. HOW TO CLEAN THE WATER INLET FILTER This screen filter should be checked periodically and cleaned if necessary. 1. Remove filter by grasping end and removing it from water inlet of pump as shown. 2. Clean filter by flushing it with water on both sides. 3. Re-insert filter into water inlet of pump. NOTE: Cone side faces out. NOTE: Do not operate pressure washer without filter properly installed. HOW TO REMOVE THE WHEELS 1. Using a 1/8" hex head wrench loosen set screw in hub collar. 2. Slide hub collar from axle and remove the tire. Filter Screen STORAGE ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for storage. PUMP The manufacturer recommends using a pump protector/winterizer when storing the unit for more than 30 days and/or when freezing temperatures are expected. If a pump protector/ winterizer is not available, *RV antifreeze needs to be run through the pump as outlined in the steps below. NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from damage. 4. If space is needed, remove handles and replace as shown. 1. Obtain a funnel, six ounces of *RV antifreeze, and 16 - 36 inches of garden hose with a male hose connector attached to one end. Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Connect length of garden hose to water inlet of pump. 4. Add *RV antifreeze to hose as shown. 5. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 6. Remove garden hose from water inlet of pump. 7. Reconnect spark plug wire. *Windshield washer fluid may also be used TROUBLE SHOOTING GUIDE CAUSE CORRECTION PROBLEM Add Fuel. No fuel. Engine will not start (see Engine Manual for further engine troubleshooting) Add required amount of oil. Low oil Squeeze gun trigger to relieve pressure. Pressure builds up after two pulls on the recoil starter or after initial use. Move choke to the “Choke” position. Choke lever in the “No Choke” position. Spark plug wire not attached. Attach spark plug wire. Place engine ON/OFF switch in ON position. Engine ON/OFF switch in OFF position. Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time. Move choke to the “No Choke” position. Fuel valve closed Move the fuel valve lever to the “Open” position. No or low pressure (initial use) Spray wand not in high pressure. See How to Use Spray Wand instructions in the Operation Section. Low water supply. Water supply must be at least 5 GPM @ 20 PSI. Leak at high pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Remove and clean filter. Water filter screen clogged. Check with Authorized Warranty Service Center (AWSC.) Defective E-Z start valve. Turn off the engine, then the water ...

Descargar ahora

Introduzca dos números de la imagen: