Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Karcher Tamaño del archivo: 1.55 mb Nombre del archivo: bb107a2d-f2a6-4855-af06-553be42faa13.pdf Idioma del manual:

DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. 3. Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it. Thermal Relief Valve READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury can occur. Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. NEVER fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. NEVER pull water supply hose to move pressure washer. This could damage hose and/or pump inlet. DO NOT use hot water, use cold water only. NEVER turn water supply off while pressure washer engine is running or damage to pump will result. DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. If you do not understand these precautions, please call 1-888-559-8550 to speak to a service representative for further instructions. TO USE SPRAY WAND The nozzles for the spray wand are stored in nozzle holder on the panel assembly. Colors on the panel identify nozzle location and spray pattern. See chart to choose the correct nozzle for the job to be performed. Black White Green Yellow Red Nozzle Color 40. low pressure 0. Spray Pattern 25. 15. Uses powerful pinpoint for very intense cleaning intense cleaning of small areas intense cleaning of larger areas covers wide areas of cleaning applies cleaning solutions Surfaces * Metal or concrete DO NOT use on wood metal, concrete, or wood metal, concrete, or wood metal, concrete, wood, or vinyl metal, concrete, wood, or vinyl The high pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of the spray. * HOW TO APPLY CHEMICALS AND CLEANING SOLVENTS Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To Apply chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as shown. 2. Place other end of chemical hose with filter on it into container holding chemical/cleaning solution. NOTE: For every 7 gallons of water pumped 1 gallon of chemical/cleaning solution will be used. 3. Install low pressure (black) nozzle into quick connect fitting of spray wand, see How To Use Spray Wand paragraph in this section. 4. After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty. NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure setting. CHANGING NOZZLES ON SPRAY WAND Risk of Flying Object could cause risk of serious injury. DO NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Pull quick connect coupler back and insert nozzle. 2. Release quick connect coupler and twist nozzle to make sure it is secure in coupler. Risk of Flying Object could cause risk of serious injury. Ensure nozzle is completely inserted in QC socket, and QC snap ring is fully engaged (forward) before squeezing gun trigger. Risk of injection or injury to person. Do not direct discharge stream toward persons, unprotected skin, eyes, or any pets or animals. Serious injury c...

Descargar ahora

Introduzca dos números de la imagen: