Iniciar sesión:
Votos - 4, Puntuación media: 4 ( )

Manual de usuario Network Computing Devices, modelo 2179

Fabricar: Network Computing Devices
Tamaño del archivo: 194.68 kb
Nombre del archivo: 2168.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


This kit will be an asset to your vehicle, meeting your air supply needs. Please take a few minutes to read through the instructions, identify the components, and learn how to properly install your Air Control Accessory Kit. NOTE: The Air Control Accessory Kit can be used with most air helper spring products. If you are installing an air helper spring kit, do not install the air line tubing into the air springs as stated in the air helper spring manual. If you are adding the Air Control Accessory Kit to an existing air helper spring system, you will need to deflate the air springs and remove the air line tubing. NOTE ON CONNECTING THE AIR LINE TUBING Cut the air line tubing as square as possible. To connect the air line tubing to the fittings, push the tubing into the fitting as far as possible. If for any reason the tubing must be removed, make sure the air helper springs are deflated, then push the collar of the fitting toward the body of the fitting and the tubing can be removed. To reassemble, make sure the tubing is cut square and push back into the fitting. PARTS LIST STEP 1 - PREPARE THE COMPONENTS A) COMPRESSOR Install the rubber isolators to the compressor in the holes located on the compressor feet. Insert the brass sleeve into the top of the rubber isolator see Figure "B". Install the threaded end of the T-fitting into the compressor head. Tighten the fitting sufficiently to engage the orange thread sealant. Next, install the pressure switch into the female end of the T-fitting. Crimp a blue female terminal connector onto the red lead from the compressor. Install the female terminal connector onto either spade on the pressure switch see Figure "A". B) AIR TANK Thread two (2) 1/4" NPT male push-to-connect fittings into the air ports on the air tank see Figure "A". Tighten the fittings securely to engage the orange thread sealant. C) GAUGE PANEL Cut two pieces of air line tubing 3-1/2" in length, making the cut as square as possible. Insert one end of each 3-1/2" piece of air line into the hole marked IN on the back of the paddle switches see Figure "C". Insert the remaining ends of the 3-1/2" lengths of tubing into a push-to-connect T-fitting see Figure "A". STEP 2 - SELECT A MOUNTING LOCATION A) COMPRESSOR ATTACHMENT Begin by removing the positive battery cable. Select a convenient location to mount the compressor. This location should provide ample air flow and be protected from airborne debris and moisture. The mounting surface should be rigid to support the compressor, such as under the hood on a fender well COMPRESSOR AIR TANK PRESSURE SWITCH DUAL AIR CONTROL PANEL 30 FT. AIR LINE TUBING 25 FT. EXTENSION HOSE #10-32 x 1" MACHINE SCREW #10-32 LOCK NUT #10 FLAT WASHER 3/8" -16 1" HEX BOLT 3/8" -16 FLNAGED HEX NUT 3/8" FLAT WASHER 5/16" FLAT WASHER 9210 9124 9016 9008 1 COMPRESSOR T-FITTING 1 1 PUSH-TO-CONNECT T-FITTING 3 1 PUSH-TO-CONNECT MALE FITTING 2 1 PUSH-TO-CONNECT 2 INFLATION VALVE 1 1 NYLON TIE 12 5 15 FT. 18 GAUGE WIRE 1 5 1...

Otros modelos de este manual:
Equipos de Bombeo - 2244 (194.68 kb)
Equipos de Bombeo - 2248 (194.68 kb)
Equipos de Bombeo - 2261 (194.68 kb)
Equipos de Bombeo - 9124 (194.68 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría