Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. The housing may need to be removed from the car on the ’71-’72 Chevelle. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the screw and aluminum back plate from the back of the new LED assembly. LED assembly standard back back for ‘71-‘72 Chevelle (attached to the assembly) (packaged separately) 6. Insert

If the gasket is hard or brittle it should be replaced. 4. Now is a good time to clean or replace the lenses and housings if necessary. If the lenses are in poor condition a replacement set is recommended. MAN#650217 5. Insert the LED assembly bulb base into the tail light housing socket. 6. Place the new LED assembly into the housing so that the aluminum mounting bracket sits into the groove for the lens gasket. 7. Replace the lens gasket. The gasket will sit on top of the aluminum mountin

2. Remove the light bulb 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the lock nut and flat plastic back plate from the back of the new LED assembly. 6. Make sure that one wire is still going through each hole in the aluminum spacer. Insert the new LED assembly through the hole where the original bulb and connector were located. Use caution

Remove the original bulb connectors from the bottom side of the housing. 2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Note that the screws and mounting plates are assembled differently for the driver side set and passenger side set. The LED assemblies will sit in the housing at an angle similar to the b

If the lenses are in poor condition a replacement set is recommended. 7. Make sure the housings and lenses are clean and dry. DO NOT remove backing from tape yet! Place the light diffuser onto the back of the lens. Check for proper fitment of diffuser to inside of lens and note the places where the tape touches the lens. MAN#650204 8. DO NOT remove the backing from the tape yet! Place the LED assembly in the housing. The wide black bar on the wire side of the LED assembly is marked to show wh

Remove the tail light housing from the vehicle. 2. Remove the bulb connector from the back of the housing. 3. Remove the 4 screws that hold the trim and lens. Remove the trim and tail light lens from the tail light housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Note that there are two different LED assemblies. One for the driver side and one for the passenger side. Select the correct assembly for the tail light housing. Remove the two locking nuts and fl

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Remove the two screws and aluminum plate from the back of the new LED assembly. 6.Insert the new LED assembly through the hole where the original bulb and connector were. Be careful when feeding the wires throughto avoid damaging insulation. 7.Feed the wires through the larger hole in themoun

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Insert the supplied rubber grommet into the hole where the original light socket was located. This will protect the wires from rubbing on the metal edge. 6. Make sure the stock lens gasket is removed from the housing and place the supplied drill template into the

B Kit Includes: m, m Installation: 1. Remove the screws and the tail light lens. 2. Remove the tail light bulb. 3. Now is a good time to clean or replace the lens and housing if necessary. 4. The new LED assembly will mount into the original light bulb socket. Push it into the socket and turn it clockwise to lock it in. 5. Repeat for the other tail light. 6. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash, you will need to upgrade your flasher. If

2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the round mounting plate from the bottom of the LED assembly. It is attached with two lock nuts. 6. Insert each new LED assembly through the hole where the original bulb and connector were located. Use caution when feeding the wires through the socket