Votos - 1, Puntuación media: 5 ( )

Fabricar: GE Monogram Tamaño del archivo: 678.39 kb Nombre del archivo: Idioma del manual:

STEP 11 Check Level Side To Side Check Level Front to Back Turn Legs to Adjust Access Hole Figure W Figure X 11 Installation Instructions SECURE DISHWASHER TO CABINET STEP 12 The dishwasher must be secured to the countertop or the cabinet sides. When countertops are made of wood, use Method 1. When countertops are granite or other materials that will not accept screws, use Method 2 to secure dishwasher at the sides. IMPORTANT — After leveling, verify that the dishwasher is still in the correct position shown in Step 10. IMPORTANT — Drive screws straight and flush. Protruding screw heads will scratch the top or sides of the control panel and can interfere with door closing. Method 1—Secure dishwasher to wood countertop • Fasten the dishwasher to the underside of the countertop with 2 Phillips screws provided. Method 2—Secure dishwasher with side mounting brackets • Remove plug buttons (one on each side). • Install screw through the hole in the side of the dishwasher and into the adjacent cabinet. Reinstall plug buttons. Both Methods—Maintain 1/2" Gap Countertop Mounting BracketsTub Frame Side Mounting Brackets Figure Y Figure AA Brackets Wood Countertop Screws Plug Buttons Side Mounting BracketsStone Countertop Figure Z Figure Y 1/2” Min. Gap Figure BB 12 Installation Instructions CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit 5/8" or 1" diameter connections on the air gap, waste tee or disposer. Cut on the marked line as required for your installation. • If a longer drain hose is required, add up to 42" of length for a total of 10 ft. to the factory installed hose. Use 5/8" or 7/8" inside diameter hose and a coupler to connect the two hose ends. Secure the connection with hose clamps. • Secure the drain hose to the air gap, waste tee or disposer with clamps. NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET FOR PROPER DRAIN OPERATION. DRAIN LINE INSTALLATION • Connect drain line to air gap, waste tee or disposer using either previously determined method. Method 1—Air gap with waste tee or disposer Method 2—“High drain loop” with waste tee or disposer IMPORTANT — When connecting drain line to disposer, check to be sure that drain plug has been removed. DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE. TIP: Avoid unnecessary service call charges. Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer. STEP 14 CONNECT WATER SUPPLY Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. • Slide ferrule against elbow and secure with compression nut. IMPORTANT — Check to be sure that door spring does not rub or contact the fill hose or water supply line. Test by opening and closing the door. Re-route the lines if a rubbing noise or interference occurs. STEP 13 90° Elbow Ferrule 90° Elbow Compression Nut Door Spring Hot Water Supply Line Figure CC Cutting Line 1" 5/8" IMPORTANT: Do not cut corrugated portion of hose Figure DD Hose Clamp Coupler Hose Clamp Figure EE Figure FF Waste Tee Installation Disposer Installation Figure GG Fasten to underside of countertop 32" Min.18" Min. Fasten to underside of countertop 32" Min.18" Min. Disposer InstallationWaste Tee Installation Remove Hopper Plug 13 Installation Instructions PRE-TEST CHECK LIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. ..Check to be sure power is OFF. ..Open door and remove all foam and paper packaging. ..Locate the Owner’s Manual in the literature package. ..Read the Owner’s Manual for operating instructions. ..Check door opening and closing. If door does not open and close freely or tends to fall, check spring cable routing and spring adjustments. See Step 1. ..Check to be sure that wiring is secure under the dishwasher, not pinched or in contact with door springs or other components. See Steps 8 and 10. ..Check door alignment with tub. If door hits tub, level dishwasher. See Step 11. ..Pull lower rack out, about half way. Check to be sure it does not roll back or forward on the door. If the rack moves, adjust leveling legs. See Step 11. ..Check door alignment with cabinet. If door hits cabinet, reposition or relevel dishwasher. See Steps 10, 11 and 12. ..Check that door spring does not contact water line, fill hose, wiring or other components. See Step 13. ..Verify water supply and drain lines are not kinked or in contact with other components. Contact with motor or dishwasher frame could cause noise. See Steps 6 and 8. ..Turn on the sink hot water faucet and verify water temperature. Incoming water temperature must be between 120°F and 150°F. A minimum of 120°F temperature is required for best wash performance. See “Prepare Hot Water Line,” page 7. ..Add 2 quarts of water to the bottom of the dishwasher to lubricate the pump seal. ..Turn on water supply. Check for leaks. Tighten connect...

Descargar ahora

Introduzca dos números de la imagen: