Regulated power infrared gas immersion tube system is optional at extra cost. A solid-state igniter board controls the gas valve and provides flame ignition. A transformer steps the control circuit voltage down to 24 volts to power the igniter board and gas valves. Gas Heated Dishwasher: For natural gas, gas pressure (customer connection) not to exceed 7" W.C. For liquefied petroleum, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C. natur

208-240/60/1 . 208-240/60/3 . 480/60/3 . 200-240/50/3* . 380-415/50/3* *Not submitted for UL/CUL Listing MODEL . AM15T OPTIONS AT EXTRA COST . Gas heat . Sense-A-Temp™ 70°F rise electric booster heater . Single point electrical connection for booster equipped machines (3 phase only) ACCESSORIES . 3.4" pressure regulator valve . Peg rack . Combination rack . Sheet pan rack . Splash shield for corner installations . Flanged and seismic feet . End of cycle audible alarm (field activated) . Delime n

Flow Pressure 4.4 4.4 Rinse Consumption - Gallons per Hour - Maximum - at 20 lbs. Flow Pressure 42.9 48.1 Rinse Cycle - Gallons per Rack - at 20 PSI Flow .74 - 180°F Min. .74 - 140°F Min. Steam Booster, if used based on 20 PSI steam - 20 PSI water flowing 130°F entering water raised to 180°F min. (50°F rise) - Lbs. per Hour 40 40 Peak Rate of Drain Flow - Gallons per Minute (Initial rate with full tank) 14 14 Exhaust Requirements 450 450 Shipping Weight Crated - Approx. lbs. - Unit only, with bo

Electrical components are wired with type ST cord. Line disconnect switch NOT furnished. CYCLE OPERATION: The microcomputer-timing program is started by closing the doors, which actuates the door cycle switch. The microcomputer energizes the wash pump motor contactor during the wash portion of the program. After the wash, a dwell permits the upper wash manifold to drain. At the end of the dwell, the final rinse solenoid valve is energized. After the final rinse valve closes, Sani-Dwell (Hot Wate

Water hardness recommended to be 3 gr. for best results. Automatic interlocks shut off pump and conveyor if door is opened when machine is in operation. CONSTRUCTION: Tank, chamber, frame, legs, control box, doors, and all panels are constructed of stainless steel. PUMP: Two 165 gpm recirculating stainless steel pumps and impeller with a ceramic seat seal. Easily accessible pumps assembly permits quick inspection. The pumps are self-draining. All piping distributing water to the upper and lower

Adequate clearances for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of make-up air in the room to allow for combustion of the gas at the burner(s). Keep the appliance area free and clear from all combustible substances. Do not obstruct the flow of combustion and ventilation air. The dishwasher must have a minimum clearance from combustible construction of 1 inch from the flue at the rear and 0 inches at the sides. A clearance of 40 inches must

8) is OFF. When the fill cycle has completed, the readout will display the wash temperature. During the rinse cycle, the rinse temperature will be displayed. Cycle Switch CYCLE SWITCH CONTROL BOX READOUT POWER SWITCH Power Switch WASH / RINSE SWITCH Wash/Rinse Switch PL-40467-1 PL-41177-1 Fig. 8 – 13 – DISHWASHING Scrape the dishes to remove large particles of food and debris. Never use steel wool on ware to be loaded into the dishmachine. Fig. 9 Stack the dishes in a rack. Do not stack dishes o

Never use steel wool to clean warewasher surfaces. Use only products formulated to be safe on stainless steel. Turn off the power switch. Open the machine doors. Clean off the dish tables into the dishwasher. Drain the machine by pulling the drain lever (Fig. 11). Remove and empty the slanted strainer and strainer bucket. Wash and rinse them thoroughly. Raise the overflow cover and remove the overflow tube. Wash and rinse the overflow tube inside and out. Remove the pump strainer (if equipped) a

A fused disconnect switch or circuit breaker must be installed in the electrical service line supplying this dishwasher and should meet the requirements of your local electrical code. The incoming power supply connections should be made to the terminal block in the control box and a ground lead should be connected to the grounding lug in the control box if grounding is not provided by the conduit used. When equipped with single point electrical connection option for both the dishwasher and elect

The serial number can be found on the machine data plate. Model AM14T Model AM14TC Model AM14F with Booster Heater shown Fig. 1 – 4 – DO NOT attempt to operate this dishwasher in the chemical sanitizing mode without a properly installed, NSF-listed, chemical sanitizer feeder (not supplied with machine). Contact an authorized detergent representative for information about a chemical sanitizer feeder. The pump motor is rated 2HP and has thermal overload protection. The fill line incorporates an at