Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Installation Mounting • Remove the mounting by holding the mounting in the direction indicated by cover. • After selecting the proper location as described on page 5 and wiring the Connector harness as described in Wiring, attach the mounting plate to the electrical box. To ensure aesthetic alignment of the alarm with the hallway, or wall, the “A” line on the mounting plate must be parallel hallway when ceiling mounted or horizontal mounted. • Pull the A.C. Quick-Connector through the center hole in the mounting plate and secure the bracket, making sure that the mounting screws are positioned in the small ends of the keyholes before tightening. • Plug the A.C. Quick-Connector into the back of the alarm (see Figure 2), making sure that the locks on the connector snap into the unit. Push the excess wire back into the electrical box through the hole in the center of the mounting plate. FIGURE 2 ATTACHING THE A.C. QUICK-CONNECTOR • Install the alarm on the mounting plate and twist the alarm in the direction of the “ON” arrow on the cover until the alarm ratchets into place (this ratcheting function allows for aesthetic alignment). Note: The alarm will mount to the bracket in 4 positions (every 90 degrees). Installation • Turn on the A.C. power. The green A.C. Power should be lit when is operating from A.• For alarms equipped with Pull the Battery Pull Tab (yellow tab protruding out of unit. This will automatically connect battery. Tamper Resist Feature To make this CO alarm somewhat tamper resistant, a tamper resist feature has been provided. Activate the feature by breaking off the four posts in the square holes in the plate (see Figure 3A). When the posts are broken off, the tamper resist tab on the base is allowed to engage plate. Rotate the alarm onto the mounting plate until you hear the tamper resist tab snap into place, locking Using the tamper resist feature will deter children and from removing the alarm. To remove the alarm, press on the tamper resist tab, and rotate the alarm off of the mounting plate (see Figure 3B). TAMPER RESIST FEATURE FIGURE 3A FIGURE 3B A Location of Posts A Operation Two labels have information on what Add the phone number of your service provider space provided. Place one label next to after it is mounted, and one label a door or window. Your new Kidde carbon monoxide is a sophisticated electronic device – yet very simple green “Power” LED will illuminate monitoring for carbon monoxide. If it levels of carbon monoxide, the red “Alarm” LED will flash accompanied with an audible alarm pattern. (See page 13 for description of alarm patterns). However, if interconnected to other Kidde alarms, or (If equipped) the backup battery is low or missing, or unit malfunctions, it will display other readings (and differently) to alert you of specific conditions. Please familiarize yourself, and other family members, to the difference between a CO alarm and an alarm signifying a problem with the unit itself. The table on Page 13 illustrates what the audible alarm patterns are, and what the recommended actions are. Operation Carbon Monoxide Alarm Indicator When the CO alarm senses a dangerous unit will emit a loud beeping pattern. The alarm pattern is 4 short beeps followed This cycle repeats as long exist. The red LED (Alarm) will flash the same pattern. WARNING: For alarms equipped with 9V battery backup, when powered by battery backup the alarm will sound and flash only once every conserve battery life. If this unit is interconnected with other Kidde the amber LED (Initiating Alarm) of the unit which first detected the CO, will light and remain on until The other interconnected CO alarms will also alarm to warn you that CO was detected. Fire Alarm Indicator When an interconnected Kidde smoke alarm detects smoke, this unit will sound a smoke/fire alarm pattern of 3 long beeps, followed by 1 second of silence. This cycle repeats as long as smoke signal persists to alert you of the condition. If this happens, leave the premises immediately by your escape plan and call your local fire department. WARNING: This unit is not a smoke alarm and will not detect smoke or fire. It will only alarm for smoke/fire if it receives a signal from an interconnected Kidde smoke alarm. Note: A smoke/fire alarm will override a CO alarm condition. Operation Function LED Display Alarm Sound Unit Status Recommendation Normal operation Green LED constantly on None Normal AC operation (sensing no CO) and None with a good battery Normal operation Green LED flashes every 7 seconds None Normal DC operation on 9V battery backup Verify AC power is restored as soon as possible to conserve battery. Replace battery Carbon monoxide alarm Red LED flashes with beeps. Amber LED shows initiating alarm 4 quick beeps, 5 seconds silence, repeating Alarm condition. Dangerous concentrations of CO Refer to alarm procedure on Page 17 detected Smoke / fire alarm Red LED flashes with beeps. 3 long beeps, 1 second silence, Receiving signa...
Otros modelos de este manual:Detector de incendios - KN-COB-IC (233.79 kb)
Detector de incendios - P/N 900-0120 (233.79 kb)
Detector de incendios - P/N 900-0120 (233.79 kb)