Votos - 5, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
If the report shows that the IP address has changed, the assignment was successful. You will see the new IP address in the report. •Static IP assignment: Use SetIP program to change the IP address from your computer (See "Setting IP address" on page 2). In an office environment, we recommend that you contact a network administrator to set IP address for your machine. Wireless network name and Network KeyWireless networks require higher security. When an access point is first set up, a network name (SSID), the type of security used and a Network Key should be created for the network. Check this information before proceeding with the machine installation. After choosing your configuration, follow the simple directions for your computer operating system, but first locate the Software CD supplied with the machine before proceeding. Installing a wireless network with the WPS buttonIf your machine and an access point (or wireless router) support Wi-Fi Protected Setup™(WPS), you can easily configure the wireless network settings by pressing the WPS () button on the control panel (See "Setting a wireless network with WPS button on the control panel" on page 2). Infrastructure mode This is an environment generally used for homes and SOHOs. This mode uses an access point to communicate with the wireless machine. •See "Installing the machine on a wireless network with an Access Point (Windows)" on page 3. •See "Installing the machine on a wireless network with an Access Point (Macintosh)" on page 6. Ad-Hoc mode This mode does not use an access point, the wireless computer and wireless machine communicate directly. •See "Installing the machine on an Ad-Hoc wireless network (Windows)" on page 5•See "Installing the machine on an Ad-Hoc wireless network (Macintosh)" on page 7 Wireless network setup (CLX-3185FW/CLX-3185WK only)_ 2 Installing a wireless network with cablesYou can install a wireless network to connect to the machine with either a USB cable or a network cable. For most users, we recommend using a USB cable with the program provided in the supplied software CD. The following are two ways to install a wireless network with cables. •With a USB cable: You can simply set up a wireless network using the program in the supplied software CD. Only Windows and Macintosh operating system are supported (See "Setting a wireless network with USB cable" on page 3). You can also install a wireless network in Printer Settings Utility with a USB cable after installing driver (Windows and Macintosh operating system are supported). •With a network cable: You can set up a wireless network using the SyncThru™ Web Service program (See "Setting a wireless network with network cable" on page 8). Setting a wireless network with WPS button on the control panelIf your machine and an access point (or wireless router) support Wi-Fi Protected Setup™(WPS), you can easily configure the wireless network settings by pressing the WPS () button on the control panel. Items to prepareYou need to ensure you have the following items ready to use: •Check if the access point (or wireless router) supports Wi-Fi Protected Setup™(WPS). •Check if your machine supports Wi-Fi Protected Setup™(WPS). Choosing your network connectionThere are two methods to connect your machine to a wireless network by using the WPS () button on the control panel. The Push Button Configuration (PBC) method allows you to connect your machine to a wireless network by pressing both the WPS button on the control panel of your machine and the WPS (PBC) button on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router) respectively. The Personal Identification Number (PIN) method helps you connect your machine to a wireless network by entering the supplied PIN information on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router). Factory default in your machine is PBC mode, which is recommended for a typical wireless network environment. Access point (or wireless router) that supports WPS (Wi-Fi Protected Setup™) has the symbol shown below. Changing WPS modeFactory default in your machine is PBC mode. To change WPS mode, follow the steps below. 1.Press Menu on the control panel. 2.Press the left/right arrow until Network appears and press OK. 3.Press the left/right arrow until Wireless appears and press OK. 4.Press the left/right arrow until WPS Setting appears and press OK. 5.Press the left/right arrow until the WPS mode you want appears and press OK. •PBC mode: Pressing both the WPS () button on the control panel of your machine and the WPS (PBC) button on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router) respectively, you can easily connect your machine to a wireless network. •PIN mode: Entering the supplied PIN number on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless router), you can manually connect your machine to a wireless network. 6.Press Stop/Clear to return to ready mode. Setting a wireless network in ...
Otros modelos de este manual:Impresoras - CLX-3180K (13.97 mb)
Impresoras - CLX-3185 (13.97 mb)
Impresoras - CLX-3185FN (13.97 mb)
Impresoras - CLX-3185FW/ETS (13.97 mb)