Iniciar sesión:
Votos - 3, Puntuación media: 4.3 ( )

Manual de usuario Design Dynamics, modelo HCM-24-RFN

Fabricar: Design Dynamics
Tamaño del archivo: 2.13 mb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


The pressure should be checked with the unit burning and set to High. Replace test point plug or tighten test screw after pressure measurement ensuring no gas leaks. PLACEMENT OF FLOOR MEDIA WARNING: Do not add extra logs or ornaments such as pine cones or vermiculite. Using these added items can cause sooting. Use only the material included in the kits. WARNING: Do not place lava rock,embersorfiberlogpieceson logs or burners. This may cause sooting.Placefloormediamaterial only on the fireplace floor. 1. Place lava rock around base of unit making sure theburnerports and valveaccess are not blocked (see Figure 8, page 9). Retain a small amount of lava rock to be used in step 4, page 9. 2. Place ember material around front and sides of unit close to (but NOT on) the burner (see Figure 9, page 9). Embers will "glow" when heated to enhance the realistic look of your log set. 115481-01B INSTALLATION Continued 3. Place fiber log pieces randomly on lava rock and ember material around unit (see Figure 10). 4. Use remaining lava rock to blend the floor media together. Your finished effect should resemble Figure 11. WARNING: Failure to position the floor media as shown in Figures 8 through 11 or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Figure 10 - Placing Fiber Log Pieces Display TRANSMITTER/REMOTE Up Arrow Down Arrow Mode Button Timer Button RECEIVER/VALVE Piezo PilotStatManual Figure 11 - Floor Media Kits Installed OPERATING APPLIANCE The RF Millivolt valve control used on these appliances allows you to turn the gas log set on or off; use a timer to automatically operate the log set; increase or decrease flame height, fan speed or timing. An easy-to-read display gives you information about room temperature, set temperature, flame height level, fan speed level and a countdown timer, as well as a low battery indication. Figure 12 shows the location of the controls and indicators for the transmitter (remote) and the receiver (valve). Note: Fan operations are not applicable to these Hardwood Series. LED Switch Knob Figure 12 - RF Millivolt Valve Controls with Transmitter/Remote 115481-01B OPERATING HEATER Continued FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: Keep flue open when operating unit. WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result causing property damage, per- sonal injury or loss of life. A. This appliance has a pilot which must be lighted with a piezo ignitor. When lightning the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor.s phone. Follow the gas supplier.s instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn gas control knob. Never use tools. If ...

Otros modelos de este manual:
Otras herramientas - HCA-18-RFN (2.13 mb)
Otras herramientas - HCA-18-RFP (2.13 mb)
Otras herramientas - HCA-24-RFN (2.13 mb)
Otras herramientas - HCA-24-RFP (2.13 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría