If fan outlet is obstructed, or Ian is not working properly, this will happen. Unit will not focus Check that the fresnel lens is properly seeted and centered In the cover cavity. To do this, remow top cover by pressing both latch taba on each side of the projector aimUteneoualy end lift cover from bottom housing. Rotate the two clastic lens locks that hold the fresnel In place, reeest the fraanel lens in its proper position end rotate lens lock Into holding position. Fresnel lena ahould be he

The filament is broken. Change the bulb. 2. the lamp is not fully plugged in its holder: Out of focus or blurring image 1. The object is too close to the lens. 2. Focus is on the max. point of “Tele” press “Wide”. 3. Auto-focus is not on: press AF again. 4. Fog on the lens in damp climate. It will disappear gradually when the equipment warms up. If the problem still remains after checking the above, consult your dealer or authorized service personnel. PACKING LIST AND ACCESSORIES: Item Quantity

FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Oper

See “Using the On-Screen Menus” on page 20 for details. FIGURE 12 Keypad and remote buttons Menu Press the menu button to open the on-screen menus. Press menu again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the on-screen menus, see page 20. source volume volume + standby menu right mouse button left mouse button LED Mouse buttons Use the mouse buttons to adjust settings in the menus. See “Using the On-Screen Menus” on page

•Make sure the lamp has not been in use for over 2,050 hours. The lamp automatically shuts off at 2,050 hours and the LED blinks orange. See “Replacing the Projection Lamp” on page 33. •Check the projector’s lamp to ensure that it is securely connected in the lamp module. Make sure the lamp door is installed. See “Replacing the Projection Lamp” on page 33. Problem: Only the start-up screen displays •Verify that the cables are connected correctly. See page 9 through page 12 for connection procedu

The three marks bellow are the caution labels for the laser beam. CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Light Window These caution labels are put on the remote control. BEFORE OPERATION VOLUME ON-OFF FOCUSZOOM VIDEOCOMPUTER D.ZOOM MENU MUTE LASER KEYSTONE NO SHOW FREEZE AUTO IMAGE NORMAL LOCK MUTE BUTTON Used to mute sound.(P21) ZOOM BUTTON Used to adjust zoom. (P20) FOCUS BUTTON U

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interf

COMPUTER MODE PICTURE IMAGE ADJUSTMENT ADJUST PICTURE IMAGE MANUALLY 1 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear. 2 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons. To change the value, press either the POINT RIGHT button or the POINT L

And connect the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the MAC/VGA Adapter is required. Terminal : MULTI-POLE 12-PIN When controlling the computer with the projector's Wireless Remote Control Unit, connect control port (PS/2, Serial or ADB port) on your computer to this terminal. (Three types of cables are supplied.) 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 2 1 6 5 4 3 10 9 8 7 12 11 Red Input Ground (Horiz.sync.) Green Input Sense 2 B

(Refer to P32) SCREEN MENU Used to set size of image to Normal or Wide. (Refer to P34) GUIDE WINDOW Shows selected item of ONSCREEN MENU. Same function as Menu for PC source. INPUT MENU Used to select input source either Computer or Video. (Refer to P22) SCREEN MENU Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (Refer to P29) BASIC OPERATION TURNING ON / OFF PROJECTOR TURNING ON PROJECTOR 1 1 Complete peripheral connections (with Computer, VCR, etc.) before turning on p