Follow the manufacturer’s directions. Most paints will spray easily if they are thinned properly. 2. Thin the paint according to manufacturer’s directions and mix thoroughly. 3. Carefully strain the paint through a paint strainer or a piece of cheesecloth. 4. Fill the Cup to 3/4 full. Close Cup. 5. Start the air compressor and set the regulator to needed pressure. Do not exceed maximum air pressure. 6. Test the consistency by spraying on a piece of scrap material. If it still appears too thick,

Addresses practices not related to personal injury. IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. WARNING – When using tools, basic precautions should alwa

Additionally, read all of the warnings and instructions provided in the instruction manual of the air compressor you will be using. WARNING: This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code 25249.5, et seq.) Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools a

If the paint is too thin, you will get poor coverage, drips and runs, and excessive drying of the paint in the air. Proper thinning varies with the mate3. rial being used and local temperature and humidity. In most cases, thinning will be approximately 10% and not more than 30%. Test the paint viscosity by dipping 4. a stick into the paint, then observing the rate paint drips from the end. Properly thinned paint will drip about 1 per second. Follow paint manufacturer’s recom5. mendations. Experi

An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly. Note: Do not use an automatic oiler system or add oil to airline. The oil will contaminate the material being propelled, ruining the final result. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and

Keep the distance from the object being painted at 6” to 9”. This may slightly differ depending on the flow adjustment and the material being sprayed. Do not stop the gun movement while spraying. If you stop the gun for even just a slight pause while spraying, the paint will build up and run down the workpiece. FIGURE 5 (Heavier coat on one side, uneven coverage) Incorrect (Even coverage) Correct (90o) 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before you Squeeze

2. Fill the Paint Cup no more than 2/3 full with your paint mixture. Press the Cap onto the Paint Cup to hold the paint. 3. IMPORTANT: Before applying paint to your work piece, test spray a piece of scrap material. In most cases both the paint mixture and spray pattern will have to be adjusted for best results. 4. To spray, squeeze the Trigger (8), as you move the Sprayer past the work material. Release the Trigger (8) at the end of each pass. Repeat until you have proper paint coverage of the w

3. Read the instructions on the paint can to determine whether or not you need to apply a fixative/adhesive to the surface to save paint. Preparing the Spray Gun 1. After making sure the paint is the proper viscosity, thoroughly mix the paint. 2. Remove the Cup Cover (19) (twist counterclockwise) and fill the Paint Cup (24) to just below the top. 3. Replace the Cup Cover (19). Twist clockwise. 4. Connect the Spray Gun to the Spiral Air Hose (46) by snapping it into place. All connections snap in

After the adjustment, tighten the Lock Ring by hand. See FIGURE 3 below. Pattern Adjustment Warning!! Never exceed the Maximum Inlet PSI of 70 PSI. 1. If you need to reduce the air pressure for specific areas, adjust the air compressor. 2. To set the pattern size specific to the job, use the Pattern Control Knob (16) (see FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (16) clockwise for a round pattern. See FIG