Box 1441 Minneapolis, MN 55440-1441 Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001 310893L Repair GMAX™ II 3900/5900/5900HD/7900 TexSpray™ 7900HD Airless Sprayers Korean patent: 10-0647761 - For Portable Airless Spraying of Architectural Coatings and Paints - 3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. GMAX ll 3900 248683 . 248684 . 248685 . . 248686 . . 249335 . . GM

Safety Setup Operation Maintenance Item 94572 For technical questions, please call 1-800-444-3353. Page 2 Table of Contents Safetye.................................................2 Specifications......................................5 Setup...................................................6 Operationa............................................9 Maintenancei......................................13 Parts List and Diagram.......................18 Warranty.........................................

Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. b. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. SAVE THESE INSTRUCTIONS. Symbol Definitions Symbol Property or Statement PSI Pounds per square inch of pressure CFM Cubic Feet per Minute flow SCFM Cubic Feet per Minute flow at standard

Related Manuals 311777 311768 US C Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Conforms to ANSI/UL Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001 standard 1450 Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When th

Mantenga un suministro de aire fresco circulando por la zona. Mantenga el conjunto de la bomba en un area bien ventilada. No dirija el chorro de pulverizacion hacia la bomba. • No fume en la zona de trabajo. • No accione interruptores de luz, motores o productos similares que pueden producir chispas en el area de pulverizacion. • Mantenga la zona limpia y sin recipientes de pintura o disolvente, trapos y otros materiales inflamables. • Conozca el contenido de las pinturas y los disolventes que e

Operation Warning! full of material. Spray Gun Air Dryer Compressor Air For best service, you should incorporate an air dryer, a regulator, and an inline air filter, as shown above. We recommend an air dryer to send moisture-free air to the Spray Gun. All are available at Harbor Freight Tools. 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the Air Inlet (#13). First, wrap the 1/4” air connector (not included) with pipe thread seal tape before connecting to a Air

Box 1441 Minneapolis, MN 55440-1441 Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001 311797F Repair GH™ 130, GH 200, GH 230, GH 300 Hydraulic Sprayers - Use with Architectural Coatings and Paints - 3300 psi (2.8 MPa, 228 bar) Maximum Working Pressure List of models provided on page 2. Important Safety Instructions. Read all warnings and instructions in this manual. Save these instructions. Contact Graco Customer Service, your local Graco distributor or our website: to obtain a manual

Ademas, puede encontrar advertencias adicionales a lo largo de este manual siempre que sea pertinente. Los simbolos que aparecen en el texto del manual se refieren a estas advertencias generales. Cuando vea estos simbolos en el manual, consulte estas paginas para obtener una descripcion del riesgo especifico. ADVERTENCIA PELIGRO DE INCENDIOS Y EXPLOSIONES Los vapores inflamables, como los vapores de disolvente o de pintura, en la zona de trabajo pueden incendiarse o explotar. Para evitar un ince

back into the thinner container. Wipe off the exterior of the Spray Gun with thinner to remove paint. If the gun becomes clogged, disassemble 4. parts 1 - 7, 9 -12 and 26 - 30 and carefully clean all the parts. To clean, use the enclosed brush (33) 5. or a cleaning kit, such as SKU# 99634 available from Harbor Freight Tools. Never use a pin or metal scraper to 6. clean the delicate components of this sprayer. You will damage the sprayer. Carefully reassemble following the 7. Assembly diagram on

An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly. Note: Do not use an automatic oiler system or add oil to airline. The oil will contaminate the material being propelled, ruining the final result. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and