• Low maintenance cost unmatched fluid section replacement cost • Equipped with Hero Uni-toolTM an all in one tool which is all you need to replace the fluid section • Stainless steel piston and cylinder sleeve for corrosion resistance and longer packing life • Long wear HytrelTM, and ThiokolTM impregnated leather packings • Industrial duty DC electric motor, fan cooled, and totally enclosed • New Flip ControlTM prime valve for positive shut off, also serves as an emergency pressure release • Qu

. Make sure drain valve is open. • Start the engine. • Open the hydraulic ball valve to allow hydraulic fluid to flow to hydraulic motor. • Paint pump should start to pump material and you should notice material flowing out to prime valve. • Let the pump run until the material is flowing evenly out of prime valve. • Close the prime valve and unit should now build up with pressure. • Run the pump until paint flows smoothly from the gun, without spitting, release the trigger. • Adjust the pump to

3500 psi (24.5 MPa, 245 bar) Maximum Fluid Working Pressure 80-130 psi (0.56-0.9 MPa, 5.6-9.0 bar) Air Inlet Pressure Range 200°F (94°C) Maximum Fluid Temperature Instructions - Parts 309550U Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. TI2408-1A US Patent Number D479,305 Korean Patent 338185 Australian Patent Number 152610 Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001

(6.4 mm x 7.5 m) 9 inch Pressure Roller Attachment IMPORTANT SAFETY INSTRUCTIONS. Read all warnings and instructions in this manual. Save these instructions. Specifications This equipment is not intended for use with flammable or combustible materials used in places such as cabinet shops or other “factory” or fixed locations. If you intend to use this equipment in this type of application, you must comply with NFPA33 and OSHA requirements for the use of flammable and combustible materials. Use w

Box 1441 Minneapolis, MN 55440-1441 Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001 310813 Rev C Repair GMAX™ 3400 Airless Sprayers Korean patent: 10-0647761 - For Portable Airless Spraying of Architectural Coatings and Paints - 3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure Read all warnings and instructions 248663 . 248664 . . 248665 . 248666 . . 310802 309639 309250 309640 .............. .............. .............. .............. Contents WARNING . . . . . . . . . . . .

Utilice agua para las pinturas al agua y alcohol mineral para pinturas al aceite. 2 Encienda la fuente de alimentacion. Gire la valvula de cebado hasta la posicion horizontal. 3 Aumente la presion a 1/2. Mantenga la pistola contra la lata de pintura. Suelte el seguro del gatillo. Dispare la pistola y aumente la presion hasta que aparezca liquido de lavado. 4 Mueva la pistola hasta el bidon de lavado, mantenga la pistola contra el bidon y disparela para lavar el sistema. Suelte el gatillo y engan

BOX 1441 MINNEAPOLIS, MN 55440- 1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001 0.9 to 3.0 gpm (3.4 to 11.4 lpm) Flow Rate 750 psi (5.1 MPa, 51 bar) Maximum Working Pressure 500 psi (3.4 MPa, 34 bar) Recommended Maximum Working Pressure Model 234113, Series A TexSpray 1030 FC sprayer, 235490 TexSpray gun and 50 ft (15 m) air and fluid hose set 309662J ‘ CONTENTS Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Component Description . . . . . . . . . . . .

**The /&@num Operating Air Pressure indicates the maxi- mum air pressure the air cap supplied with this gun was designed to operate at or below to comply with California Wood Rule 7 736. To guarantee compliance to rule 1136, the gun must be used with Air Regulator Part No. 110-776. This regulator limits the operating pressure to 10 psi (0.7 bar), using an air supply pressure of 100 psi (7 bar). U.S. Patent Nos. 3843,052; 4,386,739 United Kingdom Patent No. 2 111 406 B Patented 1984 Canada Brevet

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts. INDEX WARNINGS .................................................. 2 . 3 INTRODUCTION................................................ 4 SETUP............................................................. 5 OPERATION; ................................................. 6. 7 SHUTDOWN 8 CARE......................................... 7 FLUSHING GUIDELINES ..................................... 8

Related Manuals 311777 311767 ti8370a Model 254973 Shown US C Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Conforms to ANSI/UL Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001 standard 1450 Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to thes