Then, insert the Pump Handle back into the Container and turn the Pump Handle clockwise to secure it in place. (See Figure A.) PUMP HANDLE (43) SAFETY RELEASE VALVE (20) CONTAINER CAPACITY: MODEL 95690 = 2 GALLONS MODEL 95692 = 1.25 GALLONS (DO NOT OVERFILL) CONTAINER (31) FIGURE A 5. NOTE: The Sprayer is heavy when completely filled with liquid. Always get assistance when strapping the Sprayer onto your body. If necessary, adjust the Belt (28) for comfort. (See Assy. Diagram.) 6. Always make su

Save this manual. Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacemen

Connect the 3/8” ID Air Source Hose to the Spray Gun. 2. Set the air pressure on your compressor to 50 PSI. Do not exceed the maximum air pressure of 50 PSI. 3. Check the air connection for leaks and then disconnect the tool from the air source. Gravity Feed Sprayer Touch-Up Sprayer Air Inlet (19a) Air Inlet (14b) Fluid Adjust Knob (11a) Air Nozzle (1b) Air Adjust Valve (17a) Spray Pattern Adjust Knob (4a) Cup (2) Trigger (5b) Plastic Cup (6) Air Regulator (3b) Adjusting Screw (17b) Trigger (20a

2. Dip the Viscosity Cup into the material, and time how long it takes for the material to completely run out of the cup (See FIGURE 1). The longer it takes, the higher the viscosity. 3. In general, most materials work adequately if the viscosity is FIGURE 1 between 15 and 30 seconds. 4. If the viscosity is too high, you will have to thin the material to use it. Follow the material manufacturer’s instructions for thinning each material. 5. If you thinned materials, retest the viscosity. Note: Wh

Use two wrenches (one on the swivel (8) and one on the hose), to tighten all connections securely. 3. Refer to sprayer instruction manual for priming instructions. Installing Tip (26) and Guard (25) on Gun WARNING 1.If equipment has recently been operated, relieve pressure. Set trigger lock (2). 2.Using a pencil or similar object, insert seal (24) into back of guard (25). 3. Install guard (25) over end of gun (1). 4. Insert tip (26) in guard (25). Tighten retaining nut. Operation Spraying 1. Unl

Wear restrictive hair covering to contain long hair. 8. Use eye and breathing protection. Always wear ANSI-approved impact safety goggles. Wear an ANSI-approved respirator when spraying. 9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and hoses periodically and, if damaged

Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 17. Avoid Lead-based paints. Before beginning any paint removal process, determine whether the paint contains lead. This can be done by the local health department or paint professional using a paint analyzer to check the lead content of the paint to be removed. Lead-based paint should only be removed by a professional and should not be r

P This manual contains important Supersedes M warnings and information. and PCN P READ AND KEEP FOR REFERENCE. INSTRUCTIONS HIGH PRESSURE AIR-ASSISTED AIRLESS Model AA 2000. Spray Gun 950 psi (66 bar) Maximum Working Fluid Pressure 100 psi (7 bar) Maximum Working Air Pressure Part Number 217–292, Series C Includes spray tip of choice. U.S. Patent Nos. 3,843,052; 4,386,739 United Kingdom Patent No. 2 111 406 B Patented 1984 Canada Brevete 1984 French Patent No. 82–21202 Foreign Patents Pending Ta

3. Remove the Air Cap and soak it in solvent until it is clean. Use an old toothbrush and toothpicks to remove any material. Do not use metal objects to clean the Air Cap or you may damage the drilled passages. Inspect the fluid needle and make sure it is not bent. If it is bent, have it replaced by a certified service technician. Warning!! Do not immerse the Spray Gun Body in solvent! 4. Use the appropriate solvent (depending on the material sprayed) to wipe down the Gun body. 5. Always lubrica

A pump which runs too fast can be seriously damaged. . An air line lubricator (G) provides automatic air motor lubrication. . A bleed-type master air valve (F) relieves air trapped between it and the motor when the valve is closed. Order Part No. 107142. . The air regulator (E) controls pump speed and pressure. . An air line filter (D) removes harmful dirt and contaminants from your compressed air supply. . A drain valve (L) is required near the pump fluid outlet to relieve fluid pressure in the