Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
With a power amplifier of the correct gain (e.g. An Arcam Alpha 9P or 10P) this allows you to bi-amplify (“bi-amp”) suitable loudspeakers, giving significant improvements in sound quality (see section on BI-WIRING/ BI-AMPING). REMOTE CONTROL FUNCTIONS ■ Your Alpha 10 amplifier is supplied with the Arcam CR35 infra-red remote control handset, which has buttons to allow the simple operation of other products. It is supplied with 2 AA batteries - ensure these are inserted correctly. ■ The remote allows you to operate the Alpha 10 plus some basic functions of an Arcam or Philips based CD player (except the Alpha One CD player, which uses a different remote control language), a remote controlled tuner (such as the Alpha 8 tuner) and the Arcam Delta Black Box 500 DACC (Digital Audio Control Centre). ■ To switch the unit to standby mode press ‘STBY’. The power indicator will glow red. Press ‘STBY’ again to restore the unit to full power. ■ The MUTE button mutes the speaker connections and pre-amp outputs. Both tape outputs and the headphone socket remain active. In MUTE mode ” MUTE” will be shown on the display until mute is disabled by either pressing MUTE again or pressing volume -/+. ■ To select the brightness of the display press the button marked ‘DISP’ in the amplifier section of the remote handset to cycle through the brightness levels, off, dim or fully on. If the display is switched off pressing any front panel button, except SP1, SP2 or MODE/ZONE, or a button on the amplifiers remote control will cause the display to illuminate for a few seconds before switching off again. Section C ALPHA 10P POWER AMPLIFIER Please refer to drawing inside front cover. LOUDSPEAKER CONNECTIONS Connect up as per instructions for the Alpha 10 integrated amplifier. CONNECTING YOUR SOURCE COMPONENT 0 PWR AMP IN - Connect this input to the output sockets of your pre-amplifier or the PREAMP OUT sockets of an integrated amplifier. © MONO LINK - The Alpha 10P can be configured to provide two mono loudspeaker outputs from a single input. Using the U-link 0 supplied, connect the LINK OUT sockets together. Utilising one Alpha 10P per loudspeaker in this manner will allow bi-amplifying of bi-wireable loudspeakers. This is particularly beneficial for top quality stereo installations with a separate pre-amplifier, or for the left, centre and right channel loudspeakers in a five speaker Dolby Pro Logic system. Contact your Arcam dealer for more detailed information. ■ Daisy Chain - The Alpha 10P is capable of driving further Alpha 10P amplifiers (or any other power amplifier), to drive more speakers (eg. those in other rooms or tri-amplified speakers etc). Connect the extra power amplifier inputs to the LINK OUT sockets of the Alpha 10, left to left, right to right. FRONT PANEL 0,0 SP1 and SP2 - Pressing the SP1 switch turns on the speakers connected to the SP1 (upper) set of output terminals on the rear panel. Similarly the SP2 switch turns on the speakers connected to the SP2 (lower) set of output terminals. ■ Both the SP1 and SP2 switches can be turned on at the same time, provided that the combined impedance of the two pairs of speakers does not fall below 4 ohms per channel. ■ The SP1/2 switches will also connect/disconnect speakers attached to the 3rd channel option if fitted. Important note: If both switches are turned off then the amplifier will appear not to be functioning, as all speakers will be switched off! 0 HEADPHONES SOCKET - Accepts headphones rated between 8 ohms and 2k ohms fitted with a 6.3mm stereo jack plug. The headphone socket is always active. 0 POWER - Switches the power on and off. 0 POWER INDICATOR - This will initially glow amber. After a few seconds, it will glow green. When the indicator glows amber, the speakers are disconnected and an internal protection circuit is activated. ALPHA 10/1 OP REMOTE SWITCHING By making a connection from the “control out” socket 0 of the Alpha 10 to the “remote in” socket of the Alpha 10P power amplifier you can use the Alpha 10 to control the power mode of the power amplifier. If configured in this way the front panel power button of the Alpha 10 (or remote control standby button) will switch both amplifiers on or off simultaneously. This facility allows you to hide the power amplifier out of sight and still be able to control its functions. ENGLISH The connecting cable required is a 3.5mm to 3.5mm jack lead (stereo or mono) and it is possible to connect several 10P power amplifiers to an integrated Alpha 10 by "daisy chaining" from “control out” of one into the” remote in” of the next one, etc. THIRD CHANNEL OPTION © This option enables you to have a 5 channel amplifier in two cases, when used in addition with a suitable power amp such as the Alpha 10P, for use in a high quality Home Cinema setup. The third channel can then be used to drive the centre speaker. For connection details see instruction sheet included with third channel option. ...
Otros modelos de este manual:El receptor y el amplificador - Amplifier Alpha 10/10P (1.48 mb)