Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Place lugs between the plastic cap and the back of the terminal. Be sure to observe proper polarity, using the appropriate speaker hook-up icons for your system’s configuration. Using your fingers, tighten to obtain a positive contact. When using banana plugs, connections may be made by simply inserting the jack affixed to your speaker wire into the hole provided on the rear of the colored screw caps on the binding posts. Before using banana type jacks, make certain that the plastic screw caps are firmly tightened down by turning them in a clockwise direction until they are snug against the chassis. This will insure that the maximum surface area of the plug is in contact with the jack. Be certain to observe proper polarity. Run the cables to the speaker locations. Do not coil any excess cable, as this may become an inductor that creates frequency response variations in your system. Finally, connect the wires to the speakers, again being certain to observe proper polarity. Remember to connect your negative, or black wire, to the matching terminal on the speaker. The positive, or red wire, should be connected to the matching terminal on the speaker. NOTE: While most speaker manufacturers adhere to an industry convention of using red terminals for positive connections and black terminals for negative, some manufacturers may vary from this configuration. To assure proper phase connections, and optimal performance, consult the identification plate on your speaker terminals, or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, consult the speaker’s manufacturer for further information. Page 5 Making Rear Panel Connections When connecting the amplifier to your source equipment, match the output channel designations on the rear of your source equipment to the input jacks on the rear panel of your amplifier that have the same channel name. Correct polarity connections are important to maintain proper speaker phasing. When making connections to the amp and speakers, adhere to a consistent pattern of using one side of the wire to the red terminals and the other side to the black terminals. Right Front Speaker NOTE: The picture here is an AT2007 seven-channel model. It differs from the AT3007 only in the extra space on the panel. Other models ranging from two to six channels will only have two to six sets of balanced audio inputs, unbalanced audio inputs and speaker outputs. NOTE: This diagram shows the back of the amplifier, preamplifier and all speakers. Therefore, the right speakers are on the left side of the Center S ATI ATP8500 Preamplifier/Proces Page 6 diagram, and the left speakers are on the right side of the diagram. Right Rear Speaker Right Surround Speaker Speaker Left Front Speaker Page 7 Left Rear Speaker Left Surround Speaker essor Shown as a Typical Example Power Control Connections Your amplifier features a built-in remote turn-on system that will automatically switch the amplifier on when another device in the system is switched on. Remote Turn-On Using Products Equipped With a Low Voltage Trigger Jack Press the front panel power switch on the amplifier so that it is in the ON position. Then, using an accessory cable with a 3.5mm mono mini-plug on each end, connect the trigger-output jack on the rear of the source device to the trigger input jack on the back panel of the amplifier. When these connections are made, the amplifier will automatically turn on whenever the triggering device is turned on. Remote Turn-On Using External AC to DC Power Converter If your source device does not have a dedicated trigger jack, it is still possible to activate the unit for automatic turn on when a Switched Outlet is available on the rear of the source device. To control the amplifier in this fashion, you will need a small AC to DC power converter, capable of delivering a 3.3 to 24 volt DC signal. The DC voltage should terminate in a standard 3.5mm type mini plug. This type of converter may be obtained as a Power Adapter from many electronics retailers. When installing, press the Main Power Switch on the front panel of the amplifier in so that it is in the ON position. Plug the AC adapter into a switched outlet on the source device that will be activated when you wish to have the amplifier turn on. This may be the switched outlet at the rear of an AC receiver or other audio equipment. Connect the 3.5mm mini- plug from the adapter to the trigger-input jack on the back panel of the amplifier. The amplifier will now turn on and off automatically, based on the status of the controlling device. AC Line Connector and Power Cord Once all audio and system connections have been made, connect the supplied power cord to the amplifier first, and then connect it to an AC power source. Please make certain that the amplifier is turned off and that the device connected to the remote trigger input is off when connecting the power cord and plugging it into an AC outlet. Your amplifier is suppli...
Otros modelos de este manual:El receptor y el amplificador - AT2000 (442.08 kb)