Always wear eye and hearing protection when operating this unit. X7502831700 CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage. Introduction IMPORTANT! The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety

Always wear eye and hearing protection when operating this unit. X7502831600 CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage. Introduction IMPORTANT! The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety

Blade Installation 4-6 mm (3/16”-1/4”) Throttle Free Play Throttle trigger free play Cable Adjuster AB C 3. Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm (3/16 - 1/4 in.). 4. Connect 2 ignition stop leads from throttle cable tubing to 2 ignition leads on engine. 5. Reinstall the air cleaner cover. Remove air cleaner cover WARNING You must install the U-Handle and all Blade Conversion parts shown in the following instructions before operating this unit with a m

MANUFACTURER'S WARRANTY COVERAGE: The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative. OWNER'S WARRANTY RESPONSIBILITIES: As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO Inc. recommends that you r

Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline -Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. 2 Stroke Mixture Oil - A 2-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards mus

American made means better parts availability. Reverse tilling action Reverse action 'sucks' tiller into ground, does not walk on top of hard ground like forward rotation tillers can. Tractor HP rating 25-55 HP Gearbox Warranty 3 Years on housing, gears, shafts, seals, bearings. Shows our confidence in the product. Working Width Stamped upper hitch plate Stamped plate adds additional strength to hitch. Hitch bolted to inside of support Force is applied downward on top hitch, by bolting hi

107, 177 0.113.3702.00 ........... 13504-011 ....................... 21, 25, 53 1004020 .................... 171522038 .................... 107, 177 0.113.3703.00 ........... 41040179 ...................... 531004034 .................... 271523037 .................... 107, 177 0.113.3704.00 ........... 41040180 ...................... 17, 21, 33, 57, 1004225 .................... 171523038 .................... 103, 105, 179, 0.121.6001.00 ........... 19, 23, 29 041049 ...................... 63, 89

ion are subject to change without notice. 150 311-328S continue on next page 6/11/12 Specifications & Capacities Rotary Tillers RTR20 Series RTR2064 RTR2072 Recommended Tractor PTO HP 23-50 Horsepower (50 hp maximum) Weight 748 lbs. 795 lbs. Tilling Width 64" 72" Overall Width 70 13/16" 77 7/8" 3-Point Hitch Type Category I, Adjustable Lower Hitch Clevis with Plated Pins Fits land Pride Quick-Hitch Sideshift Capabilities 14" 1 18" Note: Limited sideshift capabilities with Land

eline ASAE Category III Heavy Duty Off-Center Shear bolt - standard Slip Clutch - optional Gearbox 50 HP Input at 540 rpm 1.46:1 Ratio Cast Iron Housing, Straight Bevel Gears Gearbox Lubrication Capacity & Type 2.2 Pints of SAE80-90W EP oil Drive Chain #80 Roller chain - Fully enclosed in oil bath with drain & fill plugs Drive chain lubricant Shell Alvania EP 00 or equivalent Sprockets Splined Bores Rotor Swing Diameter 17" Rotor Shaft Speed 220 rpm at 540 rpm PTO -i In -U-Loi

Sifted soil falls last burying the bigger items. Attachment is one all welded piece for easy assembly. Formed rear deflector with springs Formed steel gives the rear deflector additional strength. Springs allow deflector to bounce as it hits obstructions. Six tines standard on RTR20 Four tines standard on RTA20 with six being optional Six tines cut through the ground smoother. “C” Tines C Tines take less horsepower to move through the ground. 17" Rotor swing diameter For deep tilling action.