Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
• Wireless IEEE 802.11a 5 GHz Wifi configuration. • Internal NTSC / PAL or SECAM / PAL dual band TV Tuner • Multiple audio and video inputs supported. • Three external Video Inputs : S VIDEO input : one S connector AV1 input: Composite Video(three RCA Connectors- Video, L & R) AV2 input: Composite Video( one 3.5mm Mini connector– Video, L & R) • MPEG II video chip Encoder • Video Scaler : 3D video image chip • The receiving units must be within approximately 65 - 100 feet (20 – 30 meters) of the TR1a to send and receive transmissions clearly. However, this distance will vary, depending on the surroundings. At home, it is best to set up the base station in a central location, allowing more even distribution of the wireless signal to all parts of the house. • Accessories: Stand x 1,Power Adaptor x 1 (Input: 100~240VAC 1.0A max 20~30VA 50/60Hz, Output: 12VDC 1.0A 12W max) , Remote Control x 1, RCA AV Cable x 1 (for AV1 composite Video input)(3 RCA Plugs to 3 RCA plugs), 3.5mm mini jack to 3 RCA plugs AV Cable x 1 ( for AV2 composite Video input), S-video cable x 1 (For S VIDEO input)(Audio inputs of S VIDEO input are common use with Audio input RCA connectors of AV1), TV Tuner input adaptor, External Antenna x 1, IR Blaster Cable x 1, User Manual x 1, Page 3 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G REAR & FRONT SIDE PANELS / FRONT PANEL REAR & FRONT SIDE PANELS Rear Side Panel 10 1. “RJ-45” 7. “AV1” Audio R input 2. “DC 12V” power input connector RCA connector (Red) 3. “OFF/ON” Power Switch 8. “AV2” Composite Video input 4. “S VIDEO” input connector 3.5mm mini connector(Video, L, R) 5. “AV1” Composite Video input 9. “TV Tuner” input connector RCA connector (Yellow) 6. “AV1” Audio L input 10. WiFi External Antenna RCA connector (White) Front Side Panel 1 Connector for IR Blaster 2 Pre-Out 1. Connector for IR Blaster 2. Connector for Stereo Audio Pre-Out (option) Page 4 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G FRONT PANEL 3 1 2 4 1. LED 1 (Orange) Wireless LED 2. LED 2 (Green) Power LED 3. LED 3 (Red) Tuner Status 4. RESET Page 5 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G REAR SIDE PANEL 1. RJ-45 The RJ45 is for updating firmware of TR1a or hooking TR1a to Ethernet Network for Linking TR1a to all other equipment with IP addresses linked to the Ethernet Network. 2. “DC 12V” power input connector This DC 12V power input connector is for connecting 12VDC power from TR1a Power Adaptor to the TR1a. 3. “OFF / ON” Power Switch Slide the switch to left hand side will turn the power of TR1a OFF. Slide the switch to right hand side will turn the power if the TR1a ON. 4. “S VIDEO” input connector This is an input connector for “S VIDEO” sources. 5. “AV1” Composite Video input RCA connector (Yellow) This is Composite Video input RCA connector (Yellow) for AV1 for hooking to Composite Sources. 6. “AV1” Audio L input RCA connector (White) This is Audio L input RCA connector (White) for AV1 for hooking to Composite Sources. 7. “AV1” Audio R input RCA connector (Red) This is Audio R input RCA connector (Red) for AV1 for hooking to Composite Sources. 8. “AV2” Composite Video input 3.5mm mini connector (Video, L, R) This is a 3.5mm mini connector with Video, L, R for Composite Video “AV2” input for hooking to Composite Sources. 9. “TV Tuner” input connector This is a connector for hooking to TV Antenna or Cable TV's. 10. WiFi External Antenna This connector is for hooking to external 5GHz 802.11a WiFi Antenna. Page 6 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G FRONT SIDE PANEL 1. Connector for IR Blaster The 3.5mm mini connector is for IR Blaster Output. IR Blasters can be hooked up to the connector. 2. Connector for Stereo Audio Pre-Out (Option) The 3.5mm mini connector is for Stereo Audio Pre-Out. The Pre-Out is for connecting to external Stereo Audio systems and the latency between the Pre-Out and Video will have to be adjusted by time delay module. So, the Pre-Out is an option and will be installed for special designed projects and according to special orders only. FRONT PANEL 1. LED 1 (Orange) Wireless LED Blinking slowly : wireless is connecting Blinking quickly : wireless is connected and transmitting data 2. LED 2 (Green) Power LED This is a Power On LED. 3. LED 3 (Red) Tuner Status Tuner Initialization Confirmed 4. RESET This is a switch to reset TR1a. When TR1a experiences unstable operation or trouble for connecting, you can use the switch to reset TR1a by following procedure, a. Switch off the TR1a b. Press and hold the reset button and then switch on TR1a c. Wait for 5 seconds and then release the reset button. d. the TR1a should have then been reset to factory default setup. Page 7 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G Remote Control (for using with receiving units like AMC i-M15a to control TR1a through IR receiver on receiving units and WiFi ) AMC Page 8 of 17 PN: 21-TR1a_IM User manual-amc TR1a_G Function of each button on Remote Control Handset: 1. Power On/Off 2. Rescan for receiver to re-scan and ...