Votos - 3, Puntuación media: 3.7 ( )

Fabricar: MRV Communications Tamaño del archivo: 3.19 mb Nombre del archivo: Idioma del manual:

DO NOT install the machine in place where flammable gasreleases easily to avoid firehazard. ! Ensure electric leakage breakerbeing installed. Electric leakage breaker MUST be installed, otherwise electric shock may becaused. If the power supply cord isdamaged, call a certifiedelectrician of the manufacturer or other maintenance departmentto replace it. ! 10 Important Points of Safety Attention Attention points for use * Ensure ventilation of the room if the machine is used with burning facilities. Deficientventilation can cause oxygenshortage. * Check whether installation bench of the machine is damaged after a long periodof use. Machine on damagedbench may fall down and causehuman injury or other damage. * In place where winds producedby the machine can reach, donitlay any animals or plants whichmay be hurt otherwise. * Donit put vases containing water or other else on the unit assembly. Otherwise, the machine may beimmersed internally and result inbad electric insulation causingelectric shock. * The is machine CANNOT be used for the purpose of prese- rving food, animals, plants, precision instruments andartwork etc., which may bedestroyed otherwise. * DONiT replace fuse with ma- terial other than fuse of proper capacity. Replacing fuse withmetal wire or copper etc. cancause fire hazard or other faults. * DONiT lay any burning facilitiesin place where winds produced bythe machine can reach. Incompletecombustion of burning facility maybe caused otherwise. * DONiT clean the machine with water. Electric shock may occurotherwise. * DONiT put flammable sprayarticles nearby or spray them tothe machine. Fire hazard mayoccur otherwise. * DONiT operate switch with wethand. Electric shock may occurotherwise. * Stop operation and shut downmanual power switch beforecleaning and maintenance. * The power supply MUST be ofrated voltage and connected withspecial electrical supply circuit. ! 11 Operating Instructions AUTO RUN, COOL,HEAT and DRY operation Recommendations Use COOL in summer. Use HEAT in winter. Use DRY in spring,autumn and in damp climate. * AUTO MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESETFILTER RESET ON/OFF 1 SET AM SWING 2 3 4 5 SWING FRESH SET LOCKRESET HEALTH FAN TEMP MODE SLEEP CLOCK TIMER ON OFF 5 LIGHT (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display (Not Timer setting). Power indicator lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY FAN HEAT Unit will run in operation mode displayed on LCD. Stop display at your desired mode. (3) Select temp. setting Press TEMP button Every time the button is pressed, temp. setting increases 1 C. If button is kept depressed, temp.setting will increase quickly. Every time the button is pressed, temp. setting decreases 1 C. If button is kept depressed, temp. setting will decrease quickly. Unit will start running to reach the temp. setting on LCD. (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: Wire controller AUTO LOW MID HIGH AUTO Remote controller LOW MID HIGH AUTO A U T O Unit runs at the speed displayed on LCD.In HEAT mode, warm air will blow out after a short period of time due to cold-draft prevention function. In DRY mode, when room temp. becomes 2 C higher than temp. setting, unit will run intermittently at LOW speed regardless of FAN setting. (5) Unit stop Press ON/OFF button. Only time and room temp remains on LCD. All indicators go out. Vertical flap closes automatically. Hints Wire controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. Auto running: During the Auto running mode, air conditioning running and can auto-select the cooling, heating, fan mode according to the room temperature. Fan running: The AC only have air supply running no cooling and heating running at the condition, AC can't have auto air supply running, and can't display the setting temperature value on the LCD. During the heating running, after start the AC, in order to prevent cooled air, AC can stop for a while before send heat air. During the dehumification running, when the room temp. setting temp. , not setting condition according to the air speed. 12 Operating Instructions TIMER Operation SWING SET LOCKRESET HEALTH FAN TEMP MODE SLEEP CLOCK TIMER ON OFF Set Clock correctly before starting Timer operation. You can let unit start or stop automatically at following time: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF * ON MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESETFILTER RESET ON/OFF AM AM 1 SET 1 4 3 2 FRESH LIGHT 3 42 SWING (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator lights up. (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON ON ...

Descargar ahora

Introduzca dos números de la imagen: