Votos - 3, Puntuación media: 4.7 ( )

Fabricar: MRV Communications Tamaño del archivo: 3.19 mb Nombre del archivo: Idioma del manual:

Just press TIMER button several times until TIMER mode disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved. 14 Operating Instructions Sleep Function At night, before going to bed you can press down the SLEEP button on the controller and the air- conditioner will run by the comfortable sleeping mode to make you sleep more comfortable. Comfortable Sleep SWING SET LOCKRESET HEALTH MODE SLEEP CLOCK TIMER ON OFF * MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESETFILTER RESET ON/OFF AM SET OFF AM Note: Before using this function, must adjust the clock, or the sleep function will be disordered. SWING FAN TEMP FRESH LIGHT In cooling, dehumidifying mode One hour after sleeping operation start, the temp. is 1 C higher than the setting one. After another hour the temp. rises 1C and then run continuously for another 6hrs' and then close. The actual temp. is higher than the setting one which is to prevent from being too cool to your sleep. In heating mode One hour after start up, the temp. decrease 2 C lower than the setting one. After another hour decrease by more 2 C. The temperature will automatically rise by 1 C after another 3hrs' operation, and then automatically close after 3hrs' continuous operation. The actral temperature is lower than the setting one which is to prevent from being too hot to your sleep. Note: In AUTO mode, unit will run in SLEEP function according to the operation mode. After setting SLEEP function, it is forbidden to calibrate clock. If the set sleep-time does not reach 8 hours, the unit will stop operation automatically after set time is complete. Set "TIMER-OFF" function first, then set SLEEP, and the sleep-set is performance; set TIMERON function first, the sleep function can only be set before TIMER-ON; if set theSLEEP function first, the TIMER function can not be set. After setting sleep function, not allowed to adjust the clock. Can't use the remote controller operate the AC. If so, please cancel the sleep function first. After setting sleep function, can't set the timing function. about 6 hrs 1 hr 1 hr increase 1 increase 1 SETTING T SLEEP RUN BEGINS SLEEP RUN STOPS 1 hr 1 hr 3 hrs about 3 hrs decrease 2 decreases 2 increase1 SHUT DOWN SLEEP RUN STOPS SLEEP RUN BEGINS SETTING T SHUT DOWN C C C C C Heat mode Cooling mode 15 Operating Instructions Health Function * MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESETFILTER RESET ON/OFF AM SET AM SWING OFF SWING SETCLOCK LOCKRESET HEALTH FAN MODE SLEEP TIMER ON OFF TEMP FRESH LIGHT 1.How to use the health function (only for units with this function) After set the right function mode, press health button, remote controller or wire controller displays i i, oxygen pump or negative ion generator starts up to apply oxygen or negative ion to indoor unit. Press the button again,the sign i i disappeared and negative ion generator stops working. After all health function of the indoor unit being fully canceled, oxygen pump stopped. CAUTION: When the temperature of the outdoor unit is lower than 4 C, oxygen pump is automatically stopped, if press health button just then, oxygen pump could not start up. But if the air conditioner has the negative ion function simultaneous, On the "Health" mode, if you want to setting when press the health button, negative ion function could timing open mode, should close the health still be operated. When the temperature of the outdoor unit first: On the timing open mode, please don't is higher than 6 C, oxygen pump could automatically resume use health function. to oxygen-make function. Power Failure Compensation (to be applied for a necessary situation) : After the power failure compensation is set, if power failure suddenly occurs while the air conditioner is working, it will resume the previous working state when the power is supplied again. Setting Method: When the remote controller is on (excluding timer mode and fan mode), press the "Sleeping" button on the remote controller 10 times within 5 seconds, and after the buzzer rings 4 times, the air conditioner will enter the state of power failure compensation. Cancel Method: Press the "Sleeping" button on the remote controller 10 times within 5 seconds, and after the buzzer rings 2 timer, the power failure compensation mode will be cancelled. Notes: When a power failure suddenly occurs during the air conditioner is working after the power failure compensation is set, if the air conditioner will not be used for a long time, please cut off the power supply to prevent its operation from being resumed after the power is supplied again, or press the "Switch On/Off" button after the power comes again.If the controller no sleep key ,use the "swing" key instead the "sleeping" on setting the auto restart function. Concerning MRV Auto Restart function for H-MRV models Haier Auto Restart function when the unit power drops down suddenly, the unit microprocessor will store the previous working condition and ...

Descargar ahora

Introduzca dos números de la imagen: