Votos - , Puntuación media:
(
)
)
Fabricar: Harbor Freight Tools
Tamaño del archivo: 1.07 mb
Nombre del archivo: 4f599e78-5a7a-40c7-90dd-2b182ac7993b.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 -- 16.1 – 20.0 12 10 --- * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE C SKU 90045 For technical questions, please call 1-800-444-3353. Page 9 SYMBOLOGY V ~ A noxxxx/min. Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute (RPM) UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 15. WARNING! Always make sure the Power Cord (14) of the Belt Sander is unplugged from its electrical outlet prior to assembly, adding any accessories, or making any adjustments to the tool. To Remove/Install A Sanding Belt: 1. Pull out on the Tension Lever of the Front Wheel Frame (53), and slide the Sanding Belt (46) out. (See Figure D, next page.) 2. Slide a new Sanding Belt (46) on. Then, push in on the Tension Lever of the Front Wheel Frame (53). (See Figure D.) SKU 90045 For technical questions, please call 1-800-444-3353. Page 10 FIGURE D TENSION LEVER OF FRONT WHEEL FRAME (53) SANDING BELT (46) POWER SWITCH (66) FIGURE D TENSION LEVER OF FRONT WHEEL FRAME (53) SANDING BELT (46) POWER SWITCH (66) Plug the Power Cord (14) into the nearest 120 volt, grounded, electrical outlet. CAUTION: The machined parts near the Tension Adjuster (29) may be sharp. Wear work gloves when adjusting the tension. 4. Grip the Belt Sander firmly with both hands. Lift the tool and squeeze the Power Switch (66). As the Sanding Belt (46) turns, observe the Sanding Belt to see if it is turning on-center and not moving to the right or left. If the Sanding Belt moves to the right or left, while wearing heavy work gloves, turn the Tension Adjuster (29) right or left until the Sanding Belt turns on-center. Then, turn off the Belt Sander. (See Figures D, and E.) FIGURE E TENSION ADJUSTER (29) POWER SWITCH (66) SWITCH LOCK LEFT HOUSING (18) To AttachThe Dust Bag: To attach the Dust Bag (69), simply clip the opening of the Dust Bag onto the Dust Port located on the Left Housing (18). (See Figures E, and F.) DUST BAG (69) FIGURE F REV 10/04 SKU 90045 For technical questions, please call 1-800-444-3353. Page 11 OPERATING INSTRUCTIONS The Power Switch: 1. To start the Belt Sander, depress the Power Switch (66). To stop the tool, release pressure on the Power Switch. (See Figure E.) 2. To lock the Power Switch (66) in the “ON” position for continuous operation, depress the Power Switch and push in on the Switch Lock. The tool will continue to run. To turn off the tool, squeeze and release the Power Switch once. (See Figure E.) 3. WARNING! Prior to using the Belt Sander (each time), make sure the Switch Lock mechanism is working properly. Always release the Switch Lock mechanism before disconnecting the Belt Sander from its electrical outlet. Failure to do so will cause the tool to start immediately the next time it is plugged into an electrical outlet, resulting in possible injury or property damage. (See Figure E.) Proper Operation DuringThe Sanding Process: 1. WARNING! When sanding a workpiece, always push and pull the Belt Sander over the workpiece with both hands firmly gripping the tool. Never pass hands or fingers directly in front of, to the rear, or below the Sanding Belt (46). 2. Make sure the workpiece is free from nails and any other foreign objects which could damage the Sanding Belt (46). 3. Make sure the workpiece is supported at all times. Whenever possible, secure the workpiece in a vise or with clamps (not included). If necessary, use a roller stand (not included) with larger workpieces. 4. Plug the Power Cord (14) into the nearest 120 volt, grounded, electrical outlet. 5. Firmly grip the Belt Sander with both hands. Then, squeeze the Power Switch (66) to turn on the tool. If desired, use the Switch Lock to run the Belt Sander in its continuous mode. 6. Allow the Sanding Belt (46) to turn up to full speed before feeding the Sanding Belt into the workpiece. 7. To avoid damaging the workpiece, always sand parallel to the grain of the wood. SKU 90045 For technical questions, please call 1-800-444-3353. Page 12 8. Do not force the Belt Sander to remove material faster than it is designed to cut. Push and pull the Sanding Belt (46) gradually along the surface of the workpiece. 9. Once the sanding j...