Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
It's safer than using your hand and it frees both hands to operate tool. 11. DON'T OVERREACH. Keep proper footing and balance at all times. 12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and charging accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Keep handles dry, clean, and free from oil and grease. 13. DISCONNECT TOOLS. When not in use, before servicing, and when changing acces- sories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENTION CORDS. When tool is used outdoors, use only exten- sion cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate proper- ly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don't usetool if switch does not turn it on and off. 19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded sur- faces. For example; pipes, radiators, ranges, refrigerator enclosures. 20. REPLACEMENT PARTS. When servicing, use only identical replacement parts. SAVE THESE INSTRUCTIONS. VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. How to use Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation without having to keep your finger on the trigger, just pull the trigger and then push in the lock button with your thumb. To stop the tool from the lock position, simply pull the trigger again and release it. Fig. 1 Sanding tips Switch on the tool and let it run at top speed before applying to work surface. Press belt only lightly upon work: Belt ~ sander allows pinpoint sanding in close quarters. Remove side grip as in photo (Fig. 2) for tight spots. Fig. 2 Removing & installing belt Belt size 30 mm (1-3/16") x 533 mm (21") up to 32 mm(1-1/4") belt widths way be used. 1. Hold tool as shown in Fig. 3, pressing down on pulley to slacken belt. Then remove it. 2. When mounting new belt, keep arrow marks on belt and indication on pulley in same direction (Fig. 4). 3. Position the side grip as you prefer it (Fig. 5). To prolong the life of the belt, keep it running in the center of the pulley by exerting slight pressure with your hand on the grip. Pressure upon belt/workpiece surface on either side using grip will make belt move in that direction on the pulley. Fig. 3 hFig. 1 Maintenance Carbon brushes Replace carbon brushes when they wear down to about 5 mm (3/16") or sparking will occur. Both brushes should be changed at the same time. Use only identical replace- ment parts. 5mmO,, I i U I Fig. 6 Optional accessories CAUTION: The use of any other accessories not specified in this manual might be hazardous. Abrasive belts Grit Part No. Use Sheets per pack AA 40 742301-7 Coarse AA 60 742302-5 ~ I I AA120 742305-9 AA240 742335-0 AA . . . For wood, iron & steel 30 mm (1-3/16") BELT SANDER Model 9030 MACHlNE 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 23 24 26 27 28 29 31 32 33 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 DESCRIPTION T. Screw M5x15 S.Warhar 5 F. Washer 5 Fiat Shoe Gear Housing Nut M16 F. Warhsr 12 Compression Spring 13 Grip 32 H. Nut M8-17 W. Washer 12 Arm Angle Stay S. Pin 4-20 Washer 12 F. Washer 12 Pulley 30-25 Needle Bearing 1212 F. Washer 12 Wxhnr 12 Tap Pulley Shaft P. H. Screw Mx10 IWith Wxharl S. Washer 4 Side Cover Pulley 33-64 P. H. Screw M4x12 IWith Washer1 Bearing Retainer 48 Ball Bearing 6004LB Helical Gear 45 Wadruff Key 3 Pi" 4.5 Drivma Shaft MACHINE 34 1 35 2 36 1 31 2 38 2 39 3 40 1 41 1 42 1 43 1 44 1 45 1 46 1 47 2 48 1 49 3 50 1 51 2 52 1 53 1 54 1 56 1 57 1 58 3 ACCESSORY Needle Bearing 810 Rivet 0-5 Name Plate Brush Holder Cap Carbon Brush P H. Screw M4x30 IWith Wxherl FIELD ASSEMBLY IWith...