Iniciar sesión:
Votos - , Puntuación media: ( )

Manual de usuario Black & Decker, modelo 4335

Fabricar: Black & Decker
Tamaño del archivo: 2.96 mb
Nombre del archivo:

Idioma del manual:en

El documento se está cargando, por favor, espere
El documento se está cargando, por favor, espere

Resumen del manual


21407 ’ .014 Wire Diam. (30 Gage) No. 27012 .0118 Wire Diam. (33 Gage) Cotton Buffing Wheels (10" Diameter x 2/4" Hole): No. 26873 % " Wide . No. 26876 .Va” Wide CAUTION: Recommended accessories for your Bench Grinder are listed above. The use of any other accessory might be more hazardous. ADDITIONAL GRINDER SAFETY RULES 1. Always wear safety glasses or other eye protection when operating this tool, and . eye shields, mounted on the wheel guards, are strongly recommended. 2. Replace a cracked wheel immediately. Handle grinding wheels carefully to avoid bumping or dropping. DO NOT use a grinding wheel that has been dropped. Before using, inspect each grinding wheel for cracks or flaws and if these are evident, discard the wheel. 3. Before mounting a new wheel, be sure that it is marked with an R.P.M. that is the same as, or higher than, the no-load speed of the grinder as marked on the nameplate. Do not overtighten wheel nut. Use only flanges furnished with this grinder. 4. Never start a grinder with anyone, including the operator, standing in line with the wheel. After installing a replacement wheel, stand to one side and allow it to revolve freely for about one minute. 5. Do not grind on the sides of grinding wheels unless they are the special wheels designed specifically for this purpose. 6. Use of any other accessory or attachment other than those specified might create a hazard for the operator. Ю" BENCH GRINDER Cat. No. 4330, TY. 1,115V, 1 Ph. Cat. No. 4330-01, TY. 1, 220V, 1 Ph. Cat. No. 4335, TY. 1, 220/440V, 3 Ph. 1 11467 5/16-24 x % Hex head screw (12) 2 393 5/16 Lock washer (12) 3 982372 Guard cover (2) 4 6947 5/16-24 x 1 Hex head screw (2) 5 982370 Wheel guard 6 13345 1/4 -28 x Vz Round head machine screw and washer (2) 7 10257 %-10 Hex nut (L.H.) 8 982064 Outer clamp washer (2) - 9 15726 Spark shield (2) 10 15709 Tool rest (L.H.) 11 801 Flat washer (6) +36 16623 Pin 12 5531 5/16-18 x 1 Hex head screw (4) +37 34246 Brush 13 10274 Grinding wheel (coarse) +38 982954 Brush carrier 14 982063 Inner clamp washer (2) +39 17022 Sleeve 15 15711 Felt washer (2) ' +40 17020 Brush spring 16 367 10-32 x % Fillister head +41 17024 Weight machine screw (8) +42 17021 Pin 47 15705 Bearing cap 43 982952 Rotor 18 15717 Spring washer 44 19628 End housing 19 15722 Gasket 45 19624 Gasket 20 15740 Ball bearing (2) 46 15706 Bearing cap 21 405 Va -20 Hex nut (8) 47 10275 Grinding wheel (mediurr 22 416 Va Lock washer (8) 48 10256 %-1G Hex nut (R.H.) 23 15698 End housing 49 982371 Wheel guard Î24 982927 Centrifugal switch (stationary) 50 15710 Tool rest (R.H.) f25 375 10-32 x % Round head screw (3) 51 34521-01 Cover plate t26 20406 6-32 x 3/16 Terminal screw (2) 52 374 10-32 x % Round head 27 19664-61 Stator 115v. 1 phase machine screw (2) 19664-65 Stator 220v. 1 phase 53 417 #10 Lock washer (3) 19664-75 Stator 220/440v, 3 phase 54 54691 Cord clamp and nut 28 14002 Rivet (2) . 55 34522-01 Outlet box 29 61466 Nameplate +56 19325 Condenser clamp 30 15719 Stator Band +57 30390 Condenser 31 34289 Lead terminal (6) 58 995935 Base 32 22977 Drive screw (2) 59 2379 Terminal screw (4) 33 58122 Hex sticker 60 |+36965 Switch (single phase) 34 982977 Stud (4) | 25920 Switch (3 phase) 35 26587 . Woodruff key (2) 61 19326 Indicating plate +985202 Centrifugal switch (rotating) 62 24701 Hex nut includes items 36 - 42 63 72418 Caution Sticker 64 15712 Base plate 65 15723 Foot (4) 66 372 14-20 x % Round head machine screw (4) 67 406 10-32 Hex nut 68 67314 Wiring diagram label 1 phase all voltages 67315-01 Wiring diagram label 3 phase 220 volts 67316-01 Wiring diagram label 3 phase 440 volts 69 32114 Connector Special part not shown for 3 phase grinders, No. 4335 982318 Insulator (2) (3 phase only) (switch) Connection Diagrams t45699 Connection Diagram (single phase) 45700-01 Connection Diagram (3 phase) 37485 Locking Ring for #36965 switch only (single phase only) +Omit for 3 phase BULLETIN No. 2928-1...

Otros modelos de este manual:
Máquinas de rectificar - 2928-1 (2.96 mb)
Máquinas de rectificar - 4330 (2.96 mb)
Máquinas de rectificar - 4330-01 (2.96 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría