Now turn the screw in 1/8” to 1 / 4” turn increments and test cut until the blade will cut through its entire length. 2 3

Repeat this procedure until the blade cuts correctly. Hold the screw in place and retighten the locking nut. If your trimmer is pushing or bulging paper back from the edge of the trimmer, follow the previous procedure, except turn the screw clockwise, test cut, and repeat in necessary. b. If neither of the previous procedures realigns the blade, loosen the locking nut on the screw and turn the screw 2-3 full turns clockwise. Now turn the screw in 1/8” to 1 / 4” turn increments and test cut unt

Premier has manufactured trimmers for more than 50 years. During that time continuous-improvement engineering has led to virtually every major advance in trimmers. From our original wood boards, to the new PT12 Personal Paper Trimmer and TrakCut™ 512, every Premier trimmer is designed to give you years of reliable service. WARNING - Read and thoroughly understand this publication in its entirety before attempting to operate your trimmers. The trimmer blade is sharp. Never place your hands or fi

Position the left edge of the paper against the stop. Continue making cuts. IV. Maintenance 1. Cleaning and Lubrication To clean your trimmer, wipe it with a towel (or sponge) damp with a mild soap and water solution (or mild household cleaner). 2. Adjustments Over a period of years it may be necessary to realign the cutting blade. We suggest you follow this procedure for realignment. Before any adjustments are attempted, raise the blade (via the handle) to its full open position. a. At th

Premier has manufactured trimmers for more than 50 years. During that time continuous-improvement engineering has led to virtually every major advance in trimmers. From our original wood boards, to the new PT12 Personal Paper Trimmer and TrakCut™ 512, every Premier trimmer is designed to give you years of reliable service. WARNING - Read and thoroughly understand this publication in its entirety before attempting to operate your trimmers. The trimmer blade is sharp. Never place your hands or fi

On the StakCut Models (715 and 724) the paper is held securely in place by the clamp. Apply pressure to the clamp handle (item 45) as you follow step six. Warning - Make sure your fingers are not in the path of the trimmer blade!!! 6. Lower the blade with a firm, steady motion. Continue to lower the blade until the trigger latch locks. The blade will be secured in position until the next use. 7. For repeat cuts of the same dimension, use the moveable paper stop. (item 30) Move the stop to the

It should light up and the paper cradle should begin vibrating. Insert your papers. When you are finished, return the switch to the 'off position. Maintenance Bearings should be given light oil every 6-8 months. Machine and bearings should be kept free of dust and debris. Always disconnect from power before servicing. 800-658-8788 - - 800-658-8788 - www.abcoffice.com

Adjust knife guard to sit close to the knife and tighten screws. Operation This model is equipped with hand clamp (#3) which holds paper when cutting. Models IDEAL 2035 and 1036 are fitted with an automatic clamp, which goes up and down with the movement of the knife.

For a safe operation of the trimmers it is important, that the knife guard is not taken off. C. The knife carrier (#2) is fitted with a friction device. If adjusted correctly, this friction device insures, that the knife carrier (#2) with the knife cannot move down on its own from any position. D. If the knife carrier (#2) does not stay in position and moves down on its own, please re-adjust the friction device immediately. E. To adjust the friction device loosen the set screw (I) . Tighten t

Tighten the nut (II). Retighten the set screw (I). Installation The Model IDEAL 1036 does not need any assembly. On models IDEAL 1035 and IDEAL 2035 the clamp with the attached knife guard (#1) has been taken off for shipping. For re-assembling proceed as follows: Turn out screws on fixing points. Place knife guard (A) with attached clamp bar on machine as illustrated. The knife guard must be caught behind the guiding screw (B) on knife-carrier. Turn screws into fixing points (don’t tighten)