EL ABASTECIMIENTO DE COMBUSTIBLE DE UN MOTOR CALIENTE, O EN LAS CERCANIAS DE UNA FUENTE DE INFLAMACION, PUEDE PROVOCAR UN INCENDIO Y PRODUCIR LESIONES CORPORALES GRAVES Y DANOS MATERIALES. MONTAJE Instrucciones de montaje del soplador NOTA: Consulte las listas de piezas y las ilustraciones de las paginas 32-35. 1. Instale asas inferiores 15 en la parte superior de la plataforma 17 y 18. Fije con (4) tornillos de sombrerete de 5/16-18 X 1-3/4 19, (4) arandelas planas de 5/16 16 y (4) tuercas de n

– Do not blow towards people, cars, windows, or other items which could be injured or damaged by the blown debris. – Keep hands away from the blower air intake and outlet. STARTING – Start according to instructions in this manual or on the machine. – Do not change engine governor settings or overspeed the engine. Operating the engine at excessive speed can increase the hazard of personal injury. INTERRUPTING OPERATION - Before leaving the operator's position: - Park on level ground. - Shut off t

• Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Do not point blower at people or animals. • Start unit on ground with throttle at idle. Check that blower pipe is not blocked by the ground or by any objects. WARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Keep A Firm Grip • Hold handle with fingers together encirclin

Do not allow the rope to snap back in. Always hold the unit firmly. • (PB-770H): Rotate spring loaded throttle arm downward to a comfortable operating position. - PB-770 H 1. Throttle Lever Move throttle position lever (A) to IDLE DETENT positions. - PB-770 T 1. Throttle Position / Stop Switch Button Slide Throttle Position / Stop Switch Button (A) back to idle position. - PB-770 H and T 2. Choke Move choke (C) up to Cold Start Position ( ) 3. Purge Bulb Pump purge bulb (D) until fuel is visible

4. Use a tachometer to adjust idle speed to specifications found on page 11. 22 TROUBLESHOOTING Problem Cause Remedy Engine - starts hard Engine - does not start Engine Cranks Fuel at carburetor No fuel at carburetor Fuel strainer clogged Fuel line clogged Carburetor Clean Clean See your ECHO dealer Fuel at cylinder No fuel at cylinder Carburetor See your ECHO dealer Muffler wet with fuel Fuel Mixture is too rich Open choke Clean/replace air filter Adjust carburetor See your ECHO dealer Spark at

7. Remove the spark plug and pour 7cc (1/4 oz., 1/2 tablespoon) of fresh, clean ECHO 2-stroke engine oil into the cylinder through the spark plug hole. A. Place a clean cloth over the spark plug hole. B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine. C. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there. 8. Install the spark plug (do not connect ignition cable)

Cerciorese que todas las tuercas, pernos y tornillos esten bien instalados y apretados. MANTENGA EL ACELERADOR EN LA POSICION “STOP” (PARADA) MIENTRAS NO ESTE EN USO. Procure siempre que dos o mas operadores esten a una distancia segura cuando ambos operen equipos de manera simultanea. SEGURIDAD No fume mientras manipule combustible. No reabastezca de combustible el tanque, si el motor esta caliente o en funcionamiento. No reabastezca de combustible el tanque en interiores. PRECAUCION - No arran

As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. SM T W T F S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 30 14 OPERATION -Provide all

3. Clean cylinder fins (A) to allow cooling air to pass freely. 4. Replace cover and tighten screws. 5. Connect spark plug lead. A EXHAUST SYSTEM Spark Arrestor Screen Level 2. Tools required: Cross Head Screwdriver Parts Required: Spark arrestor screen P/N 14586206720, Gasket P/N V104000220 IMPORTANT Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically. 1. Remove spark plug and engine cover (five screws). 2. Remove spa

El deflector horizontal dirige la descarga de aire hacia abajo para aplicar la corriente por debajo de las hojas y desperdicios mojados y pesados. La velocidad del aire se regula mediante el control del acelerador. Al colocar el deflector en el orificio superior podra descargar un mayor volumen de aire hacia abajo. Al colocar el deflector en el orificio inferior podra descargar un mayor volumen de aire hacia arriba. Con el fin de reducir la formacion de hileras de desperdicios, o descargar el ai