Включите машину, нажав клавишу «On / Off». Откройте дверцу, потянув за ручку. Загрузите машину, не превышая массу загрузки, и закройте дверцу. Определите соответствующую программу из таблицы выбора программ в соответствии с типом белья, степенью загрязненности и температурой стирки. Установите ручку выбора программ в положение на желаемую программу-температуру стирки. Выберите подходящую скорость отжима в соответствии с выбранной программой. Если Вы используе- те дополнительную функцию, нажмит

Anti- creasingTo avoid wrinkling of your clothes, select this function. When Anti-Creasing is choosen please load less cloth, this way a special washing and spinning profile will reduce thewrinkles and your clothes will be easy to iron. 13 4 Program Selection and Starting Machine Plug you machine to outlet. Turn on the machine by pressing “On/Off” key. Open the door by pulling the handle and load the machine without exceeding loading capacity and close the door. Specify the appropriate program b

The machine starts to discharge the water. “Wash” and “Program Finished” lights will light up. • "Start/Pause/Cancel" and “Wash” lights will go off after discharging process is over and the “Lid” light will start flashing. • “Lid” lamp will light up continuously when the door is unlocked. You can select and start a new program. • If the program is cancelled in the middle of the process, “Wash” and “Program Finished” lights will light up. The machine can drain all the water or can take in water f

90.C Normally soiled, white cottons and linens. (Ex.: coffee table covers, tablecloths, towels, bed sheets) 60.C Normally soiled, fade proof colored linens, cottons or synthetic clothes (Ex.: shirts, nightgowns, pajamas) and lightly soiled white linen clothes (Ex.: underwear) 40.C 30°C Cold For delicate clothes (Ex.: lace curtains), blended clothes including synthetics and woolens. C Programs are limited with the highest spin speed appropriate for that particular type of cloth. C Sort the laundr

7 3 Installation 8 Removing packaging reinforcement 8 Opening the transportation locks 8 Appropriate installation location 8 Adjusting the feet 8 Connecting to the water supply. 9 Connecting to the drain 9 Electrical connection . 10 Destroying the packaging material 10 Disposing of the old machine 10 4 Initial preparations for washing 11 Sorting the laundry 11 Preparing clothes for washing 11 Correct load capacity 11 Loading door 12 Detergents and softeners 12 5 Selecting a program and operating

COMMON LAUNDRY PROBLEMS (cont’d) Problem Possible Cause Suggested Solution Excessive wrinkling Machine too full Water too hot Permanent press items should be washed in half-loads to prevent wrinkling. If possible, use a slower spin speed. Use lower wash temperature settings. Rips, snags, Sharp objects in pockets Empty all pockets and turn inside out before laundering. excess wear Hooks, snaps, zippers, buckles Harsh chemicals Existing rips and tears Permanent press items Fasten all hooks, snaps,

After cancellation, the symbol of the corresponding step at which the cancellation was made will remain lit and “End” label will appear on the screen. Program in rinse hold mode • This process is shown with the flashing Spin Symbol (Figure 3- 13c) and the lit up Standby Symbol (Figure 3-13k). If you wish to spin when the machine is in this mode: Adjust the spin speed. Press “Start/ Pause/Cancel” button (Figure 2-10). The program continues, pumps out the water and spins. Standby Symbol (Figure 3-

Setting can be made in intervals of 30 minutes. 1. Open the loading door, place the laundry inside and fill with detergent. 2. Set the washing program, temperature, spin speed and, if required, select the auxiliary functions. 3. Press “Time delaying” buttons “+” and “-” (Figure 2-8) to set your desired time delay. Time delaying symbol (Figure 3-13h) will flash. 4. Press “Start/Pause/Cancel” button (Figure 2-10). Then the time delay starts to count down. Time delaying symbol (Figure 3-13h) will l

Taking Care of your Washer/Dryer Exterior cleaning Wipe the outside of your machine with a damp, soapy cloth. Do not use harsh chemicals or abrasive items to clean plastic parts. Coin Trap cleaning Clean the coin trap at least four times a year. Be sure unit has drained before opening trap door. • Place towel or pan under trap door (Fig. 12) to catch any water. • Remove trap by turning it slowly counterclockwise until water appears. (Fig. 13). • Empty water through coin trap. Pull coin trap stra

C The auxiliary functions in the table may differ according to the model of your machine. 19 EN Auxiliary functions Auxiliary function selection keys 11a 11b 11c 11d • Depending on the program, you can select the desired auxiliary function by pressing the keys 11a, 11b, 11c, 11d. • Select the required auxiliary functions before starting the program. • Some combinations cannot be selected together. (Ex.: Prewash (Figure 2-11a) and Quick Wash (Figure 2-11b). • Symbol of the selected auxiliary func