3. Depress the safety nose mechanism against your workpiece. 4. Before pulling the trigger, move your free hand and other body parts out of the way of any potential path of a deflected nail. 5. Pull the trigger. — If the nail drove into the wood far enough, continue with your intended operations. — If the nail either went too far or not far enough, then go to the Adjusting Depth subsection on Page 11. -10- H7943 /H7944 Framing Nailer Adjusting Depth A depth adjustment device is attached to the n

Do not use any oil that will corrode the rubber O-ring seals such as detergent oils or oils that are used as solvents. With these points in mind, you can operate your nail gun under the best conditions for increased dependability and low overall cost of operation. IMPORTANT: When you first pick up an air activated nail gun you must always assume that it is loaded. Inspect for any nails and load the gun magazine before connecting the gun to the air supply. Do not connect the air supply until yo

3. KEEP WORK AREA CLEAN. 7. DO NOT FORCE TOOL. It will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. DO NOT USE IN DANGEROUS 8. USE THE RIGHT TOOL. Do not ENVIRONMENT. Do not use pneuforce tool or attachment to do a job matic tools in damp or wet locafor which it was not designed. tions, or where any flammable or noxious fumes may exist. Keep work area well lighted. 9. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Safety

Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the equipment. Inventory After you open the nailer box, you should find the following. Model H7949/H7950/H7951 Inventory (Figure 1) A. Nailer.................................................. 1 B. Nailer Case ........................................ 1 C. O-Rings.............................................. 2 D. Pneumatic Tool Oil ........................

.. .. .. .. .. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ...... ...... ......

6. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit -13 7. Taking care not to scratch or dent the nailer parts, use a wooden dowel or similarly shaped tool to push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. Clean and inspect the parts for cracks, wear, or burrs. 8. Apply a thin film of pneumatic t

To protect yourself from serious personal injury, DO NOT allow your air compressor to exceed the recommended pressure when connected to this nailer! Quick Connector Quick Lubricator Your Tool Quick Coupler Connector n=0Q Hi Regulator Air Compressor Air Hose Quick Coupler Filter Figure 2. Typical filter/lubricator/regulator installation order. H8230/H8231 15° Roofing Nailer -5- Safety Check A safety mechanism on the nose of the nailer protects against accidental firing. The n

To reduce your risk from these hazards, always wear ANSI approved safety glasses or a face shield. In addition, this nailer discharges at up to 85-90 decibels. To reduce your risk of hearing loss from operating this nailer, always wear ANSI approved ear protection. Awarning Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed to reduce the risk of serious injury. To fire a nail: 1. Connect the nailer to your air supply. 2. Depr

Ignoring this warning may result in serious personal injury. 2. Slide the magazine pusher to the rear of the magazine and pivot the pusher down until it catches in the lock notch on the magazine as shown in Figure 3. Figure3. Locking the pusher. 3. With the pusher locked at the rear of the magazine, insert a strip of staples into the magazine as shown in Figure 4. Figure4.Loading a staple strip into the magazine. 4.Lift the pusher out of the lock notch and guide it forward to push the staple str

Clear all ports and blow the solvent away with compressed air. 9. Replace any part that shows damage or heavy wear. Relubricate the tool. 10. Apply a thin film of the stapler lubricating oil on the new O-ring and place it on the new piston. Install any other parts included in the piston repair kit. 11. Insert the new piston in the cylinder. With the magazine cover open, gently push the piston down to make sure the piston driver moves freely into the driving hole. Note: DO NOT force the piston in