Suitable for timber frames, roofing, joist and a host of other applicationsMakita now have a better solution with this easily portable machine. Gas nailer GN900SE Fire up to 7,200 7.2v Li-ion batteryUse of a li-ion battery allowsfor compact and lightweighttool design. 30 min charge time. Hex wrench Attached to the machine for easy access to adjust the depthof the nail drive. Gas cell chamber Quick and easy load system. LED lightservice indicator Green: Good batteryRed: Low/dead batteryOrange: Er

Failure to maintain sufficient lubrication will cause O-rings to wear quickly. (1) Oiler <2) Pneumatic oil Keep the air hose away from heat (over 60°C, over 140°F), away from chemicals (thinner, strong acids or alkalis). Also, route the hose away from obstacles which it may become dangerously caught on during operation. Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. La SECURITE et la FIABILITE de cet outil ne seront préserves qu

Positionnez donc vos clous avec soin. (1) Clou A nail will be bent or the tool can become jammed if you mistakenly nail on top of another nail or strike a knot in the wood. The nail may be thrown and hit someone, or the tool itself can react dangerously. Place the nails with care. (1 ) Nail Maintenez fermement la pièce à clouer. Sous l'impact de lacloueuse, elle pourrait se déplacer dangereusement sans cette précaution. Hold the workpiece securely. Under nailer impact, the workpiece can fly

You can perform nailing operations with less fatigue by doing so. A nail will be bent or the tool can become jammed if you mistakenly nail on top of another nail or strike a knot in the wood. The nail may be thrown and hit someone, or the tool itself can react dangerously. Place the nails with care. I Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you le

Securing the trigger in the ON po- sition is also very dangerous. Never attempt to fasten the trigger. Do not operate a tool ifany portion of the tool operating controls is inoperable, disconnected, altered, or not working properly. I Operate the tool within the specified air pressure of 4.5 -8.5 kgf/cm*G(65 -120 PSIG) for safety and longer tool life. Do not exceed the recom- 8 5 kgf/cm2G 8 5 kgf/cm2G (120 PSIG) (120 PSIG) mended max. operating pressure of 8.5 kgf/cmzG (120 PSIG). The tool shoul

Air supply hoses shall have a minimum working pressure rating of 10.7 kgf/cm2G (150 PSIG) or 150 percent of the maximum pressure produced in the system whichever is higher. CAUTION: Low air output of the compressor, or a long or smaller diameter air hose in relation to the nailing frequency may cause a decrease in the driving capability of the tool. Lubrication To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to the tool. Adjust the oiler so t

* Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. CAW= TUECC I~ICTRIIrTinhic Erin EI ITI IRE RCCCRCMPC IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. .For personal safety and proper operation and maintenance of the tool, read this instruction manual carefully before usi

2-114". 2-112") Min. hose diameter I Dimensions IL x W x H) I Net weight 310 mm x 133 mm x 305 mm 6,5 mm 1114,,) I (12.3/16" x 5.1/4" x 12") I kg 16'' Ibs) * Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWA

15 GAUGE (DA) 7jiakita. 2-1/2" finish nailer WELL BA LANCED PNEUMJ 1/4" - 2-1/2" 15 Ga DURABILITY IC 15 GAUGE (DA) FINISH NAILER uge DA Style Finish Nails with a Capacity of 120 Nails se Protects the Wood Surface for a Quality Finish omfortable Operation ring and Installation, Hardwood Floor Installation, e Manufacturing and More FINISHED TO PERFECTION Model AF633 Features & Benefits ■ Aluminum magazine holds 120 15 gauge DA style finish nails (1-1/4" to 2-1/2") ■ Easy loading,angled