** As applicable. *** For use on Globar® dryer models ONLY. Telephone: (508) 678-9000 Fax: (508) 678-9447 16 American Dryer Corporation 88 Currant Road / Fall River, MA 02720-4781 Main Door Assembly Illus. No. Part No. Qty. Description 1* 800136 1 Main Door Assembly Complete (includes illus. nos. 1 through 12) 800133 1 Main Door Assembly Less Accessories (includes illus. nos. 1, 2, and 3) 800134 1 Main Door with Glass and Gasket ONLY (includes illus. nos. 1, 2, 3, 5, and 6) 2 103050 1 12-1/2” St

12 Lint Drawer Assembly for Models Mfd. as of July 29, 2005 ....................................................................................... 13 Lint Drawer Assembly for Models Mfd. prior to July 29, 2005 .................................................................................... 14 Tumbler Assembly for Models Mfd. as of May 2004 .................................................................................................. 15 Tumbler Assembly for Models Mfd. prior to May 2004

No. Part No. Qty. Description 1 2 150006 152013 2 2 #6-32 x 7/8” Phillips Pan Head Machine Screw #6-32 Hex Nut 3 153010 2 #6 Star Washer 4 137005 1 Main Door Switch ONLY 5 6 881702 882298 881687 882291 150301 1 1 1 1 2 Main Door Switch Housing Assembly Complete (white) (includes illus. nos. 1 through 5) Main Door Switch Housing Assembly (wrinkle coral blue) (includes illus. nos. 1 through 5) Main Door Switch Housing ONLY (white) Main Door Switch Housing ONLY (wrinkle coral blue) #8-18 x 7/16” Ph

(56Z frame) 6 150501 4 5/16-18 x 3/4" Hex Head Machine Bolt 7 153002 4 5/16" Lock Washer 8 153001 4 5/16" Flat Washer 9* 100075 1 1 HP 220/230/380/460v 3O 50/60 Hz T.E.F.C. Motor with 3/4" Shaft (56Z frame) 10 120200 1 3/8" x 90. Connector 814779 1 3-Phase (3O) Blower (Fan/Impellor) Motor Harness 11 150501 4 5/16-18 x 3/4" Hex Head Machine Bolt 12 153002 4 5/16" Lock Washer 13 153001 4 5/16" Flat Washer 14 154000 8 5/16" Tinnerman Nut 15 152004 7 5/16" Hex Nut 16 153002 4 5/16" Lock Washer 17 15

nos. 1 through 5 and 7 through 9) 881746 1 Phase 6 OPL Reversing Computer Panel Assembly Complete (includes illus. nos. 1 through 5 and 7 through 9) 3 137123 1 Phase 6 OPL Non-Reversing Microprocessor Controller ONLY 137122 1 Phase 6 OPL Reversing Microprocessor Controller ONLY 4 150005 2 #6-32 x 3/4” Phillips Round Head Machine Screw 5 153010 2 #6 Star Washer 6 150309 1 #10-32 x 1/2” Hex Head TEK Crimptite Screw 7 136048 1 1/8-Amp (slo blo) Fuse 8 136017 1 3.15-Amp (fast acting) Fuse 9 136019 1

Proper cap screw torque is 30 ft.-lb. If greater tightening forces are applied, excess pressures will be created in the hub of the mounted sheave, which may cause it to crack. To Replace Motor Pulley Discontinue electrical power to the dryer. Remove the lint drawer. Remove the lint door. Loosen V-belts, then rotate pulley and roll V-belts out of its’ grooves. Remove cap screws from bushing. Insert cap screws in tapped removal holes and tighten evenly until bushing becomes loose on shaft. Refer

Loosen the tension bolts. Remove old V-belts. Reverse these steps to replace V-belts. NOTE: Always replace V-belts in pairs. Motors To Replace Drive Motor Discontinue electrical power to the dryer. Remove the lint drawer. Remove the lint door. Remove the left lint wall. Remove the drive V-belts. Follow V-belt replacement from motor to speed reducing shaft. Loosen the four bolts securing the motor to the base of the dryer. Disconnect the motor wiring. 18 American Dryer Corporation 450431-3 450431

Remove rear belt guard. Loosen V-belts. Rotate pulley and roll V-belts out of grooves. Remove setscrew from the 9-inch (22.86 cm) pulley. Remove pulley and key. NOTE: A gear puller may be required to remove pulley. Reverse this procedure for replacement. NOTE: Pulley must be aligned for proper operation. Drive Motor Pulley Replacement Discontinue electrical power to the dryer. Remove rear belt guard. Loosen V-belts. Rotate pulley and roll V-belt out of groove. Remove setscrew from the drive moto

display on microprocessor controller (computer)... Open circuit breaker switch or blown fuse. Tripped blower motor overload. Faulty wiring connection. Faulty transformer. “Emergency Stop” (E-Stop) button is depressed. Faulty microprocessor controller (computer). Computer will not accept keypad entries... Keypad ribbon is not plugged into computer securely. Faulty keypad. Faulty microprocessor controller (computer). Dryer will not start, but computer L.E.D. indicators are on... Failed contactors.