Proper cap screw torque is 30 ft.-lb. If greater tightening forces are applied, excess pressures will be created in the hub of the mounted sheave, which may cause it to crack. To Replace Motor Pulley Discontinue electrical power to the dryer. Remove the lint drawer. Remove the lint door. Loosen V-belts, then rotate pulley and roll V-belts out of its’ grooves. Remove cap screws from bushing. Insert cap screws in tapped removal holes and tighten evenly until bushing becomes loose on shaft. Refer

No. Part No. Qty. Description 1 2 150006 152013 2 2 #6-32 x 7/8” Phillips Pan Head Machine Screw #6-32 Hex Nut 3 153010 2 #6 Star Washer 4 137005 1 Main Door Switch ONLY 5 6 881702 882298 881687 882291 150301 1 1 1 1 2 Main Door Switch Housing Assembly Complete (white) (includes illus. nos. 1 through 5) Main Door Switch Housing Assembly (wrinkle coral blue) (includes illus. nos. 1 through 5) Main Door Switch Housing ONLY (white) Main Door Switch Housing ONLY (wrinkle coral blue) #8-18 x 7/16” Ph

display on microprocessor controller (computer)... Open circuit breaker switch or blown fuse. Tripped blower motor overload. Faulty wiring connection. Faulty transformer. “Emergency Stop” (E-Stop) button is depressed. Faulty microprocessor controller (computer). Computer will not accept keypad entries... Keypad ribbon is not plugged into computer securely. Faulty keypad. Faulty microprocessor controller (computer). Dryer will not start, but computer L.E.D. indicators are on... Failed contactors.

Hi-Limit Manual Reset 23 318700 1 Pipe Bracket (bent) 24 143000 1 3/4” to 1/2” Reducing Coupling 25 154004 1 Twin Speed Nut 26 802799 1 Sail Switch Box Cover and Bracket ONLY 27 122200 1 Sail Switch ONLY 28 150303 2 #4 x 3/4” Pan Head “A” Machine Screw 29 105500 1 Sail Switch Actuator Rod 30 319202 1 Sail Switch Damper (flat) 31 154002 1 1/8” Push On Fastener ** 882772 1 Steam to Gas Interface Plate...Not Illustrated * Consult factory for elevations over 2,000 feet. ** Needed when converting fro

To expedite processing, the following procedures must be followed: No parts are to be returned without prior written authorization R.M.A. from the factory. Note: An R.M.A. is valid for only 30 days from date of issue. The R.M.A. issued by the factory, as well as any other correspondence pertaining to the returned part(s), must be included inside the package with the failed merchandise. Each part must be tagged with the following information: Model number and serial number of the dryer from which

nos. 1 through 5 and 7 through 9) 881746 1 Phase 6 OPL Reversing Computer Panel Assembly Complete (includes illus. nos. 1 through 5 and 7 through 9) 3 137123 1 Phase 6 OPL Non-Reversing Microprocessor Controller ONLY 137122 1 Phase 6 OPL Reversing Microprocessor Controller ONLY 4 150005 2 #6-32 x 3/4” Phillips Round Head Machine Screw 5 153010 2 #6 Star Washer 6 150309 1 #10-32 x 1/2” Hex Head TEK Crimptite Screw 7 136048 1 1/8-Amp (slo blo) Fuse 8 136017 1 3.15-Amp (fast acting) Fuse 9 136019 1

(Refer to Taper Lock Bushing and Drive Motor Pulley Replacement on the previous page.) 9) Remove the taper lock bushings from the drive wheels. 10) Slide the pillow block bearings and taper lock bushing inward towards the gear (speed) reducer on the drive shaft. 11) Lift the end of the drive shaft closest to the rear of the dryer and pivot the other end of the shaft on the drive wheel until the shaft can be removed from the dryer. 12) To install new drive shaft, reverse Step #11 thru Step #2. 13