Votos - 3, Puntuación media: 4.7 ( )

Fabricar: JVC Tamaño del archivo: 2.67 mb Nombre del archivo: Idioma del manual:

L-AUDIO-RUSBVIDEO/YPbPrINPUT4 Front inputs on C and 735 series models. L-AUDIO-R VIDEO/Y Pb Pr USBI N P U T 4 HDMI 4DVI AUDIO HDMI 4 input available on 736 and 835 series models. Front inputs on 736 and 835 series models. Front Panel Indicators and Power Button 1.LAMP indicator shows lamp condition (usually off during normal TV operation). 2. STATUS indicator. Off during normal TV operation. 3.POWER/TIMER indicator. Lit when TV is powered on; flashes when TV is powered off and the auto-on TV Timer is set. 4.POWER button. Turns TV on and off; works the same as the POWER key on the remote control. See the next page for more on front- Indicator LED lights and POWER button 1 3 42 panel indicators. 1. Television Overview Front-Panel Indicators Off Steady On Slow Blinking Fast Blinking POWER/TIMER Indicator LED Color TV Condition Additional Information None TV is powered off. Normal operation. Green TV is powered on. Normal operation. Green TV powered off, auto-on timer is set. Normal operation. TV can be turned on at any time. • TV just plugged into AC outlet. Green • AC just restored after power failure. • TV is rebooting after System Reset used. • TV is rebooting after power fluctuation or receiving abnormal digital signals from a digital channel or digital device. • You have begun the procedure to update software from an authorized flash memory device. STATUS Indicator Wait approximately two minutes for blinking to stop before turning on. Normal operation. LED Color TV Condition Additional Information Normal TV on or standby condition. Normal operation. None TV is too hot. The TV will display a warning message and shut off if it overheats. Yellow • Ambient room temperature may be too high. Turn off the TV and let the room temperature to drop. • Clear blocked air vents. Ensure at least a four-inch clearance on all sides of the TV. • Clean the lamp-cartridge air filter. See Appendix E. Red TV may require service. Turn off the TV and unplug the set from the AC power source. Wait one minute and then plug the set back in. See Appendix D. If the LED is still on, contact your dealer or a Mitsubishi Authorized Service Center. Go to or call 1-800-332-2119 to receive Authorized Service Center information. LAMP Indicator LED Color TV Condition Additional Information None Normal TV on or standby condition. Normal operation. Green TV just powered off and lamp is cooling. Starts to blink 60 seconds after turning off TV. TV can be turned back on before blinking starts or after blinking stops, but not while the indicator is blinking. Normal operation. Yellow 1. Lamp access door is open or not secure. TV will not operate until lamp access door is secure. See Appendix E for installation information. 2. No lamp installed. TV will not operate without a lamp. See Appendix E for installation information. Red Lamp no longer illuminates and has reached the end of the lamp life. Replace the lamp. The TV will not operate when the lamp no longer illuminates. See Appendix E for installation information. TV Back Panel 1. ANT 1/ANT 2 (Antenna) If you are connecting an antenna or direct cable service without a cable box, connect the main antenna or cable source to ANT 1. Use ANT 2 for a second source. ANT 1 and ANT 2 can each receive digital and analog over-the-air channels from a VHF/UHF antenna or non- scrambled digital/analog cable source. 2. AVR AUDIO OUTPUT Use AVR AUDIO OUTPUT to send analog audio of the program currently shown on the screen to an analog A/V surround sound receiver or stereo system. Digital audio from digital channels and HDMI devices is converted to analog audio by the TV. This is the only audio connection needed between it and the TV if using an analog A/V receiver or stereo system. 3. DIGITAL AUDIO OUTPUT This output sends Dolby Digital or PCM digital audio to your digital A/V surround sound receiver. Analog audio from analog channels and devices and HDMI devices is converted by the TV to PCM digital audio. If you have HDMI 3D GLASSES EMITTER AVR AUDIO OUTPUT DIGITAL AUDIO OUTPUT L R AUDIO LR (480i / 480p / 720p / 1080i)LR DVI/PC INPUT VIDEOAUDIOR L Y Pb Pr AUDIO Pb Y/ VIDEO Pr VIDEO: 480i/480p/720p/1080i/1080pAUDIO: PCM STEREO PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p/ 1080p 1 2 3 HDMI IR-NetCommand Output / ExternalController Input RINPUT 3INPUT 2INPUT 1S-VIDEO INPUT 3 ANT 2 / AUX ANT 1 / MAIN 1 65 72 3 49 5 89 11 10 4 IR NetCommand Output/ External Controller Input available on 736 and 835 series models. 1. Television Overview a digital A/V receiver, in most cases this is the only audio connection needed between the TV and your A/V receiver. 4. Composite Video (INPUT 1, INPUT 3) Use the VIDEO jacks to connect a VCR, DVD player, standard satellite receiver, or other A/V device to the TV. Use the adjacent AUDIO R and L inputs for INPUT 1 or INPUT 3 if you wish to send audio to the TV. Note that the INPUT 3 composite video jack is automatically disabled when you connect to S-VIDEO ...

Descargar ahora

Introduzca dos números de la imagen: