Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Mitsubishi Electronics Tamaño del archivo: 2.67 mb Nombre del archivo: Idioma del manual:

• Press SYSTEM RESET button and wait for blinking to stop. • If blinking continues, service is required. Contact your dealer or a Mitsubishi Authorized Service Center to arrange for a service evaluation. Listings of Mitsubishi Authorized Service locations can be obtained from our web site, tv.com or by calling 1-800-332-2119. NetCommand Symptom Remarks 1. Cannot see the menu from the A/V Receiver. A/V Receiver Set Up for Audio-Only Switching • The A/V Receiver is not connected to any video input of the TV. To check the A/V Receiver menu, temporarily plug into an unused input of the TV, such as Input 3. Exit the Auto Input Sensing screen and select Input 3 from the Input Selection menu. Press MENU. A/V Receiver Set Up for Audio and Video Switching over HDMI • Use the MENU key on the A/V receiver’s remote control. A/V Receiver with NetCommand for • HDMI. Press INPUT to open the Input Selection menu. Highlight the A/V receiver icon and press MENU. 2. NetCommand unable to learn specific device keys. A/V Device does not use IR format for remote control • signal. ITT and RF formats cannot be learned. Room lighting may affect the signal. Have the remotes very • close (6 inches or less) to the TV during Learning. If learning a Mitsubishi remote control, make sure slide • switch is not set to TV position. Some, but not all, device key functions can be learned by • NetCommand. For example, POWER and PLAY may be learned, but other functions may not. The signal from the remote control may not be strong • enough. Insert fresh batteries and try Learning again. NetCommand Symptom Remarks 3. The A/V receiver is the selected audio source but there is no sound. A/V Receiver Set Up for Audio-Only Switching • Check to see if the A/V Receiver power is turned on. - With A/V receiver power turned on, redisplay the - Input Selection menu and press ENTER to allow NetCommand to correctly select the A/V Receiver input. Incorrect setup in the Inputs > AV Receiver menu. - Check the device connection assigned in the AV Receiver menu. A/V Receiver Set Up for Audio and Video Switching over HDMI • Check to see if the A/V Receiver power is turned on. - If the device is connected only to the TV (e.g., on ANT1, - ANT 2, or a front panel input), verify that the TV’s AUDIO OUTPUT is connected to the A/V receiver. The A/V receiver is not switching properly because - you have not learned the inputs. See “Setting Up NetCommand Control of an A/V Receiver,” page 57. 4. There is no sound from the A/V receiver for my DVD player or other surround sound device even though I learned the IR code for the A/V receiver’s DVD input or other input. (A/V Receiver Set Up for Audio-Only Switching) NetCommand A/V receiver setup for the DVD player or digital surround sound device or other device is not switching properly. See chapter 6, “NetCommand IR Control,” and perform A/V receiver setup for a digital surround sound device as described under “A/V Receiver Control: Automatic Audio Switching,” page 58. 5. There is no sound or picture from the A/V receiver for my DVD player or other device connected to the A/V receiver; the A/V receiver should be sending video to the TV over an HDMI cable. (A/V Receiver Set Up for Audio and Video Switching over HDMI) NetCommand A/V receiver setup is not switching audio and video inputs properly. See “Setup to Control Automatic Video and Audio Switching via HDMI,” page 61. 6. I’ve selected my DVD player or other surround sound device in combination with the TV speakers but hear no sound from the TV speakers. A/V Receiver Set Up for Audio-Only Switching • If you have only an audio connection from the device to the A/V receiver, a physical audio connection from the device to the TV is also required. Connect the left and right audio output from the device - to the appropriate TV audio input. Now you can hear audio from the device through either the TV speakers or the A/V receiver. To switch audio sources, press AUDIO, press -to show the Speakers option, then press to select AV Receiver or TV. A/V Receiver Set Up for Audio and Video Switching over HDMI • With your DVD player connected to the A/V receiver, only video is passed from the A/V receiver to the TV because of copy-protection restrictions on the HDMI signal 7. I “learned” the RECORD key for my VCR/DVR but when I pressed the RECORD key, the VCR/DVR did not record anything. Check that the VCR or DVR is receiving a signal directly from your cable box or satellite receiver. Appendices Appendix E: Lamp-Cartridge Replacement and Cleaning Appendix E: Lamp-Cartridge Replacement and Cleaning WARNING THE ACCESS PANEL IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING PANEL COMPLETELY. CAUTION BURN DANGER! HOT SURFACES INSIDE! Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do not tilt as glass may ...

Descargar ahora

Introduzca dos números de la imagen: