Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
com. Samsung’s Wireless LAN adapter supports the IEEE 802.11A/B/G and N communication protocols. Samsung recommends using IEEE 802.11N. When you play the video over a IEEE 802.11B/G connection, the video may not play smoothly. ..NOTE xx You must use the “Samsung Wireless LAN Adapter” (WIS09ABGN) to use a wireless network. xx Samsung’s Wireless LAN adapter is sold separately. The WIS09ABGN Wireless LAN adapter is offered by select retailers, Ecommerce sites and Samsungparts.com. xx To use a wireless network, your TV must be connected to a wireless IP sharer. If the wireless IP sharer supports DHCP, your TV can use a DHCP or static IP address to connect to the wireless network. xx Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure. xx If you apply a security system other than the systems listed blow, it will not work with the TV. xx If Pure High-throughput (Greenfield) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will not support a connection in compliance with new Wi-Fi certification specifications. xx If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode. xx If your router, modem, or device isn’t certified, it may not connect to the TV via the “Samsung Wireless LAN Adapter.” xx Connection Methods: You can setup the wireless network connection six ways. –– Samsung Auto Configuration –– PBC (WPS) –– Auto Setup (Using the Auto Network Search function) –– Manual Setup –– SWL(Samsung Wireless Link) –– Ad-Hoc xx All of Samsung Wireless LAN Adapter should be connected directly to the TV’s USB port. USB HUB are not supported. TV Rear Panel (HDD) The LAN Port on the Wall LAN Cable Wireless IP sharer Samsung Wireless LAN Adapter or .. To use the SWL(Samsung Wireless Link) function, connect to the USB 1 (HDD) port. Notice The picture may appear corrupted or have static for some channels when the TV is connected to the Samsung Wireless LAN Adapter. In such case, establish a connection using one of the following methods: Method 1 Method 2 Connect using the USB right angle adapter Connect via an extension cable 04 Advanced Features or Network Setup (Samsung Auto Configuration) This function is available in APs (Access Points) that support Samsung Auto Configuration. If your AP does not, you can connect through PBC (WPS), auto, or manually. . This function is available when SWL(Samsung WirelessLink)is set to Off. . You can check for equipment that supports Samsung Auto Configuration on How to set up using Samsung Auto Configuration 1. Place the AP and TV next to each other and turn them on. . Because the booting times of applications differ, you may have to wait for approximately 2 minutes. . If the LAN cable connected the WAN port of AP during Samsung Auto Configuration, you are able to complete until internet connection test. If you do not connect, Samsung Auto Configuration will check only device connecting of AP (Not check internet). 2. After 2 minutes, connect the Samsung Wireless LAN Adapter to the TV. When the Samsung Wireless LAN Adapter is established, the pop-up window appears. 3. As soon as a connection is established, place the AP in parallel with the Samsung Wireless LAN Adapter giving a gap no larger than 25cm. 4. Wait until the connection is automatically established. . If the connection fails, reset the AP and then try again. . If Samsung Auto Configuration does not connect your TV to your AP, a pop-up window appears on the screen notifying you of the failure. Reset the AP, and then try again. If the connection fails again, choose one of the other connection setup methods, PBC (WPS), auto, or manual. 5. After the connection is established, locate the sharer at the desired location. . If the AP settings have been changed or it is the first time you use the new AP after purchase, you need to set up again beginning from Step 1. Network Setup (PBC (WPS)) How to set up using PBC (WPS) If your router has a PBC (WPS) button, follow these steps: 1. Connect your TV to your LAN as described in the previous section. 2. Turn on your TV, press the MENU button on your remote, use the ^ or Ў button to select Setup, and then press the ENTEREbutton. 3. Use the ^ or Ў button to select Network in the Setup menu, and then press the ENTEREbutton. 4. On the Network screen, select NetworkType. 5. Set NetworkType to Wireless. 6. Select Network Setup. The Network Setup screen appears. English 31 Advanced Features Network Setup PBC(WPS) U Move E Enter R Return Select a network : Not Selected > Internet Protocol Setup : Auto IP Address : Subnet Mask : Gateway : DNS : Auto DNS Server : 7. Press the ...
Otros modelos de este manual:TV - UE32C6700US (37.02 mb)
TV - UE32C6710US (37.02 mb)
TV - UE32C6730US (37.02 mb)
TV - UE32C6740SS (37.02 mb)