Iniciar sesión:
Votos - 4, Puntuación media: 4 ( )

Manual de usuario Electrolux, modelo VESBMR

Fabricar: Electrolux
Tamaño del archivo: 460 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Like all light bulbs, halogen bulbs require periodic replacement. When the bulbs in your unit have burned out you will notice or more of the following: • Contrasting light is dark • Flame is dim or dark in certain areas • Log set ember bed appears dim or dark in certain areas WARNING: Do not install replacement bulbs that exceed specified maximum watts. Your unit must be opened in order to replace the light bulbs. To reduce the number of times you need to open the unit, replace all bulbs at the same time. Removing Top of Unit 1. Unplug unit from the power supply. 2. Remove the two screws at the rear of the unit which secure the top to the back frame. 3. Two clips hold the top to the sides. Push the top of the unit toward the back until the clips disconnect. Remove top of the unit and place face up on the floor. 4. Unscrew the 4 screws from the metal plate and set plate aside. Figure 5 - Stove Top Removal Replacing Top Contrasting Bulb 1. The housing for the top contrasting light is connected to the top of the mirror. Remove housing from mirror by gently lifting up. CAUTION: Do not force the light housing off the mirror. This may damage the mirror (e.g. chipping, cracking, etc.) 2. Remove screws from each side of housing. 3. Carefully reach into the housing and remove spring clip. Hold socket and pull out the old bulb. 3. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. 4. Set aside until all bulbs have been changed. Figure 6 - Removing Housing and Top Contrasting Bulb Screw Housing Mirror Front of Stove 117190-01B CLEANING AND MAINTENANCE Continued Replacing Log Set Ember Bed Bulbs 1. Carefully remove mirror from unit by lifting it gently from the stove. Store in a safe place or lay it face down on the carpet. 2. From the bottom, lift up the log set ember bed and remove it from the unit (do not pull up on logs). 3. Remove spring clip from bulb. Hold socket and pull out old bulb. 4. Hold socket and push in new bulb. Replace spring clip. 5. Repeat steps 2 and 3 for the second bulb. Figure 7 - Ember Bed Bulb Replacement (Looking in from Top of Unit) Log Grate Bulb with Spring ClipBulb with Spring Clip Replacing Flame Generation Bulbs 1. Unscrew the 6 screws from back of stove shown in Figure 8. Remove metal plate. AVOID STRESS TO THE WIRES. Figure 8 - Locating Flame Generation Cylinder Grounding Connecting Screw Screws Screws Screws 2. Locate the flame generation cylindrical drum. It is constructed of two removable halves; either of which can be removed from the unit. 2. Squeeze half of drum cylinder until it's top edge clears the top drum track. Remove bottom edge of cylinder drum from bottom drum track. This will give you access to the light bulbs. Note: Do not exert excessive pressure on drum cylinder as this may cause damage. 3. Remove spring clip. Hold socket and pull out old bulb. 4. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. 5. Repeat steps 5 and 6 for second b...

Otros modelos de este manual:
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría