Iniciar sesión:
Votos - 3, Puntuación media: 3.7 ( )

Manual de usuario Jenn-Air, modelo VESBL

Fabricar: Jenn-Air
Tamaño del archivo: 460 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Removing Top of Unit 1. Unplug unit from the power supply. 2. Remove the two screws at the rear of the unit which secure the top to the back frame. 3. Two clips hold the top to the sides. Push the top of the unit toward the back until the clips disconnect. Remove top of the unit and place face up on the floor. 4. Unscrew the 4 screws from the metal plate and set plate aside. Figure 5 - Stove Top Removal Replacing Top Contrasting Bulb 1. The housing for the top contrasting light is connected to the top of the mirror. Remove housing from mirror by gently lifting up. CAUTION: Do not force the light housing off the mirror. This may damage the mirror (e.g. chipping, cracking, etc.) 2. Remove screws from each side of housing. 3. Carefully reach into the housing and remove spring clip. Hold socket and pull out the old bulb. 3. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. 4. Set aside until all bulbs have been changed. Figure 6 - Removing Housing and Top Contrasting Bulb Screw Housing Mirror Front of Stove 117190-01B CLEANING AND MAINTENANCE Continued Replacing Log Set Ember Bed Bulbs 1. Carefully remove mirror from unit by lifting it gently from the stove. Store in a safe place or lay it face down on the carpet. 2. From the bottom, lift up the log set ember bed and remove it from the unit (do not pull up on logs). 3. Remove spring clip from bulb. Hold socket and pull out old bulb. 4. Hold socket and push in new bulb. Replace spring clip. 5. Repeat steps 2 and 3 for the second bulb. Figure 7 - Ember Bed Bulb Replacement (Looking in from Top of Unit) Log Grate Bulb with Spring ClipBulb with Spring Clip Replacing Flame Generation Bulbs 1. Unscrew the 6 screws from back of stove shown in Figure 8. Remove metal plate. AVOID STRESS TO THE WIRES. Figure 8 - Locating Flame Generation Cylinder Grounding Connecting Screw Screws Screws Screws 2. Locate the flame generation cylindrical drum. It is constructed of two removable halves; either of which can be removed from the unit. 2. Squeeze half of drum cylinder until it's top edge clears the top drum track. Remove bottom edge of cylinder drum from bottom drum track. This will give you access to the light bulbs. Note: Do not exert excessive pressure on drum cylinder as this may cause damage. 3. Remove spring clip. Hold socket and pull out old bulb. 4. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. 5. Repeat steps 5 and 6 for second bulb. 6. Insert bottom edge of removed cylinder half into bottom drum track. Gently squeeze drum cylinder until it's top edge fits into top drum rack. 7. Replace the metal plate with screws. 8. Replace the log set ember bed. 9. Replacethemirror. Note:Beforereplacing,clean mirror of any dust or fingerprints. Make sure the mirror side is toward the front of the unit. 10. Replace the top contrasting light housing. Note: The contrasting light should be placed at the mid point of the mirror edge. 11. Replace the...

Otros modelos de este manual:
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)
Placas - CGESBMR (460 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría