Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 6.2 40415 AND40425 WALLCONTROLS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 6.3 OPERATING 40415 / 40425 CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 6.4 WALLCONTROLS CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 7MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21 7.1 BIANNUAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21 7.2 ANNUAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 8PARTS ORDERINGCHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 9TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 3 1. TYPICAL INSTALLATIONS (CONT’D) 1.2 INSTALLATION FOR HEPA 4100 ONLY (CONT’D) 1.2.2 HEPA 4100 ATTIC INSTALLATION All 3 types of installations can be used in the attic (Stand Alone, Central Draw Point or Return-Return). The example shown below is a Return-Return installation (connection to a forced air system). CAUTION Due to the potential temperature difference between the attic and the rest of the house, all unit ducts must be insulated. CAUTION The attic temperature must always be above 0°C (32°F). A portion of stale air is exhausted to the outside and the rest is drawn to the unit. Outside fresh air is blended with interior air and then filtered. This filtered air is supplied to the return (plenum) of the forced air unit. To avoid cross-contamination and achieve the highest efficiencies, the forced air system blower must always be ON. See figure below. NOTE: Home with multiple forced air systems should have 1 unit on each system. VH0051 CAUTION Do not connect the HEPA 4100 to any forced air system supply duct. - 6 3. BEFORE STARTING 3.1 INSPECT THE CONTENTS OF THE BOX WARNING ! To avoid risk of suffocation, discard the plastic bag wrapping the unit and the wall control. • Inspect the exterior of the unit for shipping damage. Ensure that there is no damage to the door, door latches, main switch, etc. • Inspect the interior of the unit for damage. Ensure that blower assembly, heat recovery core, insulation, dampers, MERV8 filter (HRV 2600 or HR 2.6 units only) prefilter and HEPA filter (HEPA 3100, HF 3.1 or HEPA 4100 units only), etc. are all intact. 3.2 TOOLS, MATERIALS AND INSTALLATION KITS Here are the tools and materials needed to perform the installation: - Phillips screwdriver #2 or Robertson #1 - Hammer and flat blade screwdriver (for plenum connection installation only, to make holes in existing metal duct) - Scissors or utility knife (to cut duct tape) -Duct tape -Tin snips or metal shear (for plenum connection installation only, to cut ductwork) - Aluminum duct tape (for plenum connection installation only) - Jig saw -Caulking gun and caulking For HRV 2600 and HR 2.6 units, the installation kit is #15273. For HEPA 3100, HF 3.1 and HEPA 4100 units, the installation kit is #13932. 3.3 LOCATING THE UNIT Choose an appropriate location for the unit. • Within an area of the house where the ambient temperature is between 10°C (50°F) and 65°C (149°F) (basement, furnace room, closet, etc.). • So as to provide easy access to the interior of the unit, for filter maintenance. • Close to an exterior wall, so as to limit the length of the insulated flexible duct to and from the unit. • Away from hot chimneys and other fire hazards. • Allow for a power source (standard 3-prong grounding outlet). • Close to a drain. If no drain is close by, use a pail to collect run-off. (For HRV 2600, HV 2.6, HEPA 3100 and HF 3.1 units only.) - 8 4. WALL CONTROL INSTALLATION (CONT’D) VD0170 A 7. Turn the unit switch knob to OFF position in order to unlock the door. Unlatch the door and open it. If required, the door can be removed. To do so, remove the stopper (A) located on the right side of the door hinge. Then, hold the door and hit with your palm its left side. Slide the door to the right to disengage it from the unit. VO0019 8. Using a screwdriver, remove the 2 retaining screws of the front plate and carefully remove the front plate from the unit. VD0088 9. Using a small rod, pierce a hole through the unit at the end of the wire channel in front of the unit. (See picture beside.) Splice back the end of the cable to access the 4 wires. Remove the insulated sleeve of each wire ends. Insert the end of the cable through the unit, using the small hole previously done. ...
Otros modelos de este manual:Los aficionados - HEPA 3100* (4.18 mb)
Los aficionados - HRV 2600* (4.18 mb)