Votos - 3, Puntuación media: 4.3 ( )

Fabricar: CFM Tamaño del archivo: 36.34 kb Nombre del archivo: Idioma del manual:

Fan should not be turned on and off rapidly. 9. Do not use fan with a solid state speed control device. 10. Do not allow fan to become wet or damp. 11. Do not block air intake or exhaust from fan. 12. Do not allow foreign objects to enter fan and come in contact with fan blades. S SSP PPE EEE EED DD S SSE EEL LLE EEC CCT TTO OOR RR S SSW WWI IIT TTC CCH HH Fan is equipped with either a 2-speed or 3-speed pull chain switch, allowing user to select desired airflow. Pulling a speed selector switch repeatedly will cause fan speed to cycle as follows: 2 22- --S SSp ppe eee eed dd S SSw wwi iit ttc cch hh: :: OFF – FIRST SPEED – OFF – SECOND SPEED – OFF 3 33- --S SSp ppe eee eed dd S SSw wwi iit ttc cch hh: :: OFF – HIGH – MEDIUM – LOW – OFF A AAS SSS SSE EEM MMB BBL LLY YY I IIN NNS SST TTR RRU UUC CCT TTI IIO OON NNS SS M MMO OOD DDE EEL LLS SS S SSE EEF FF- --1 110 00 T TTH HHR RRO OOU UUG GGH HH S SSE EEF FF- --2 224 44 C CCo oon nnt tte een nnt tts ss: :: Pre-assembled guard mount fan, shutter, shutter mounting hardware kit, package of mounting screws. To mount shutter to fan assembly: 1. Shutter mounting hardware kit includes: 4 rubber vibration isolators, 4 nylon inserts, 4 screws (#12 x 1”) and 4 rubberized washers. 2. Insert screws into washers - rubber side down. 3. Place nylon inserts into square holes of corner gussets at rear of shutter. 4. Place shutter face down (gusset side up). Center vibration isolators over nylon inserts. 5. Place fan assembly on shutter so that wire hooks on fan guard are centered over vibration isolators and nylon inserts. Junction box must be positioned at bottom with shutter blades opening upwards. 6. Secure fan assembly to shutter using screws and washers. 7. Ensure that fasteners are snug. Do not over tighten to avoid stripping nylon inserts. M MMO OOD DDE EEL LL S SSE EEF FF- --3 330 00 C CCo oon nnt tte een nnt tts ss: :: Pre-assembled guard mount fan, shutter, shutter mounting hardware kit, package of mounting screws. To mount shutter to fan assembly: 1. Shutter mounting hardware kit includes: 4 rubber vibration isolators, 8 rubber inserts, 8 screws (#8-32 x 11/2”) and 8 rubberized washers. 2. Insert screws into washers - rubber side down. 3. Place rubber inserts into round holes of corner gussets at rear of shutter. It may be necessary to twist and push or tap lightly to seat rubber inserts properly. 4. Place shutter face down (gusset side up). Center vibration isolators over rubber inserts. 5. Place fan assembly on shutter so that wire hooks on fan guard are centered over vibration isolators and nylon inserts. Junction box must be positioned at bottom with shutter blades opening upwards. 6. Secure fan assembly to shutter using screws and washers. 7. Ensure that fasteners are snug. Do not over tighten to avoid pulling out rubber inserts. M MMO OOD DDE EEL LLS SS P PPE EEF FF- --1 110 00 T TTH HHR RRO OOU UUG GGH HH P PPE EEF FF- --3 330 00 C CCo oon nnt tte een nnt tts ss: :: Pre-assembled panel mount fan. ...

Descargar ahora

Introduzca dos números de la imagen: