Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
TOP: The time stamp will show on the top. (4) WATER MARK : ON: Shows a water mark on the picture when copying image to USB flash memory. OFF: This erases the water mark on the picture when copying image to USB flash memory. (5) RESOLUTION: The resolutions for NTSC are 720x480, 720x240 and 360x240 to be selected. Its default value is 720x240. The resolutions for PAL are 720x288, 720x576 and 360x288 to be selected. Its default value is 720x288. 35 (6) RECORD MODE: REWRITE: Continue recording. Disk will be overwritten if it is full. STOP: Stop recording when disk is full. 36 3.4 ALARM SETUP MENU In the ALARM SETUP MENU, we define : (1) ALARM: ENABLE: Enable alarm detection. DISABLE: Disable alarm detection. (2) ALARM TYPE: N. O. : Normal Open alarm. N. C. : Normal Close alarm. N.O. Trans.: When the alarm is triggered, buzzer starts to function no matter how long the alarm duration is set until you set it back to N.O. N.C. Trans.: When the alarm is triggered, buzzer starts to function no matter how long the alarm duration is set until you set it back to N.C. (3) ACTIVE CAMERA: Active camera setting, from camera 01~08. You can set the camera which corresponds to the place where the alarm is located. Note:The recording camera number in an event depends on the alarm number, and the active camera images will not be recorded. Example: You assign camera 3 as the active camera to alarm 1. When the alarm 1 is triggered, camera 3 will be displayed and camera 1 will be recorded. 37 (4) DURATION: Buzzer noise and event record duration of an alarm, from 1 sec to 99 seconds. The default value is 5 seconds. (5) ALARM OUTPUT: The setting of alarms which are NONE and 1, where 1 means the alarm is enabled. (6) ALARM EMAIL: Select “YES” for sending an email when alarm occurs. The email address can be set in the NETWORK SETUP MENU. (7) BUZZER: Alarm buzzer. ENABLE: To enable an alarm buzzer. DISABLE: To disable an alarm buzzer. (8) ALARM NETWORK: YES: Enable alarm network. NO: Disable alarm network. (9) MAIN MON: Display on a main monitor when an alarm occurs. NO CHANGE: Nothing changes on the display in the main monitor when an alarm occurs. FULLSCREEN: A full screen will pop up when an alarm occurs. (10) CALL MON: Display on a call monitor when an alarm occurs. NO CHANGE: Nothing changes on the display in the call monitor when an alarm occurs. SEQUENCE: Display in the sequence mode when an alarm occurs. ACTIVE CAMERA: Display the active camera in full screen mode to the call monitor. (11) SUMMARY : Dial Jog to change items in the SUMMARY table. All alarm’s statuses are shown in SUMMARY tables. These tables are for checking alarm overall statuses, but not for setting. Note : Please check APPENDIX C to see other available alarm input / output functions. 38 3.5 MOTION SETUP MENU In the MOTION SETUP MENU, we define : (1) MOTION: ENABLE: Enable motion detection. DISABLE: Disable motion detection. Note: Motion only works in live and playback modes. It is invalid when you are setting menus. (2) SENSITIVITY: The sensitivity allows users to adjust to a suitable motion detection sensitivity. There are 10 sensitivities available; level 1 is the lowest, and level 10 is the highest sensitivity. (3) DURATION: Buzzer noise and event record duration of an alarm, from 1 sec to 99 seconds. The default value is 5 seconds. (4) ALARM OUTPUT: The setting of alarms which are NONE and 1, where 1 means the alarm is enabled. 39 (5 ) EMAIL/NETWORK: YES: Send an email / Enable alarm network when an alarm occurs. NO: Do not send an email / Disable alarm network when an alarm occurs. The email address and e-mail server can be set in the NETWORK SETUP MENU. (6) BUZZER: Motion buzzer. ENABLE: To enable a motion buzzer. DISABLE: To disable a motion buzzer. (7) MAIN MON: Display on a main monitor when a motion occurs. NO CHANGE: Nothing changes on the display in the main monitor when a motion occurs. FULLSCREEN: A full screen pops up when a motion occurs. (8) CALL MON: Display on a call monitor when a motion occurs. NO CHANGE: Nothing changes on the display in the call monitor when a motion occurs. SEQUENCE: Display in the sequence mode when a motion occurs. ACTIVE CAMERA: Display the active camera in full screen mode to the call monitor. (9) SUMMARY: Dial Jog to change items in the SUMMERY table. All motion’s statuses are shown in SUMMARY tables. These tables are for checking motion overall statuses, but not for setting. 40 (10) EDIT MULTIPLE MOTION AREA Enter a desired channel, and press SELECT to edit a motion area. Please make sure that MOTION is set as “Enable” before entering the motion detection area. In the motion edit mode: The default motion area of each camera is entire screen which displays in light green. Press COPY to start to set an area. Then press SEARCH to end and enable the area, or press PAUSEto end and disable the area. Dial JOG to select a horizontal or a vertical area, and press ENTER to switch a horizontal or vertical area. Press MENU to...
Otros modelos de este manual:Vídeo - 410H (1.93 mb)
Vídeo - EDR810H (1.93 mb)
Vídeo - 810M (1.93 mb)